MAX3110ECWI+G36 Maxim Integrated Products, MAX3110ECWI+G36 Datasheet - Page 11

• Manufacturer Part Number: MAX3110ECWI+G36
• Description: IC UART/TXRX RS232 W/CAPS 28SOIC
• Manufacturer: Maxim Integrated Products
• Type: SPI/MICROWIRE-Compatible UART with Integrated ESD-Protected RS-232 Transceiverr

Specifications of MAX3110ECWI+G36

• Features: Transceiver
• Number Of Channels: 1, UART
• Protocol: RS232, RS485
• Voltage - Supply: 4.5 V ~ 5.5 V
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Package / Case: 28-SOIC (0.300", 7.50mm Width)
• Data Rate: 250 Kbps
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Supply Current: 0.6 mA
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Description/function: SPI/MICROWIRE-Compatible UART with integrated ESD-protected RS-232 transceiver
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 5 V
• Propagation Delay Time Ns: 150 ns
• No. Of Channels: 1
• Uart Features: SPI/QSPI/MICROWIRE-Compatible µC Interface, Internal Charge-Pump Capacitors
• Supply Voltage Range: 4.5V To 5.5V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Figure 2. Compatible CPOL and CPHA Timing Modes
Figure 3. Detailed Serial Timing Specifications for the Synchronous SPI Port
The MAX3110E/MAX3111E are compatible with SPI,
QSPI (CPOL = 0, CPHA = 0), and MICROWIRE serial-
interface standards (Figure 2). The MAX3110E/
MAX3111E have a unique full-duplex-only architecture
that expects a 16-bit word for DIN and simultaneously
produces a 16-bit word for DOUT regardless of which
read/write register is used. The DIN stream is moni-
tored for its first two bits to tell the UART the type of
data transfer being executed (see the Write
Configuration Register , Read Configuration Register ,
Write Data Register , and Read Data Registe r sections).
DIN (MOSI) is latched on SCLK’s rising edge. DOUT
(MISO) should be read into the µP on SCLK’s rising
edge. The first bit (bit 15) of DOUT transitions on CS’s
falling edge, and bits 14–0 transition on SCLK’s falling
Protected RS-232 Transceivers with Internal Capacitors
SPI/MICROWIRE-Compatible UART and ±15kV ESD-
SCLK
SCLK
SCLK
SCLK
DOUT
DOUT
DIN
SCLK
CS
DIN
CS
(CPOL = 0, CPHA = 0)
(CPOL = 0, CPHA = 1)
(CPOL = 1, CPHA = 0)
(CPOL = 1, CPHA = 1)
______________________________________________________________________________________
MSB
MSB
t
CSO
14
14
13
13
t
DV
t
CSS
t
DS
12
12
t
DH
11
11
10
10
SPI Interface
t
CL
9
9
8
8
t
CH
7
7
6
6
• • •
• • •
• • •
• • •
5
edge. Figure 3 shows the detailed serial timing specifi-
cations for the synchronous SPI port.
Only 16-bit words are expected. If CS goes high in the
middle of a transmission (any time before the 16th bit),
the sequence is aborted (i.e., data does not get written
to individual registers). Most operations, such as the
clearing of internal registers, are executed only on CS’s
rising edge. Every time CS goes low, a new 16-bit
stream is expected. An example of using the Write
Configuration Register is shown in Figure 4.
Table 1 describes the bits located in the Write Config-
uration, Read Configuration, Write Data, and Read
Data Registers. This table also describes whether the
bit is a read or a write bit and the power-on reset state
(POR) of the bits. Figure 5 shows an example of parity
and word-length control.
5
4
4
3
3
2
2
t
DO
1
1
LSB
LSB
t
CSH
COMPATIBLE
WITH MAX3110E/MAX3111E
NOT COMPATIBLE
WITH MAX3110E/MAX3111E
t
TR
t
CS1
11