TDA2003AV STMicroelectronics, TDA2003AV Datasheet
TDA2003AV
Specifications of TDA2003AV
Available stocks
Related parts for TDA2003AV
TDA2003AV Summary of contents
Page 1
... DC and AC short-circuit protection between all pins and ground, a thermal limiting circuit, load dump voltage surge protection and protection diodes in case of accidental open ground. Table 1. Device summary Order code TDA2003AV TDA2003AH June 2011 10 W car radio audio amplifier Pentawatt (vertical) Package Pentawatt (vertical) ...
Page 2
Contents Contents 1 Schematic, test circuits and pin connections . . . . . . . . . . . . . . . . . . . . 5 2 Electrical specifications . . . . . . . ...
Page 3
TDA2003A List of tables Table 1. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
List of figures List of figures Figure 1. Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 5
TDA2003A 1 Schematic, test circuits and pin connections Figure 1. Schematic diagram Figure 2. DC test circuit Figure 3. AC test circuit Schematic, test circuits and pin connections Doc ID 018796 Rev 2 5/19 ...
Page 6
Schematic, test circuits and pin connections Figure 4. Pin connections (top view) 6/19 Doc ID 018796 Rev 2 TDA2003A ...
Page 7
TDA2003A 2 Electrical specifications 2.1 Absolute maximum ratings Table 2. Absolute maximum ratings Symbol Vs Peak supply voltage (50 ms supply voltage Vs Operating supply voltage Io Output peak current (non-repetitive) Io Output peak current (repetitive) P Power ...
Page 8
Electrical specifications Table 4. Electrical characteristics (continued) Symbol Parameter V Input sensitivity i B Frequency response (-3 dB) d Distortion R Input resistance i Gv Voltage gain (open loop) Gv Voltage gain (closed loop) (1) e Input noise voltage N ...
Page 9
TDA2003A 2.4 Electrical characteristics curves Figure 5. Quiescent output voltage supply voltage Figure 7. Output power vs. supply voltage Figure 9. Gain vs. input sensitivity (R Figure 6. Quiescent drain current vs. supply voltage Figure 8. Output power vs. load ...
Page 10
Electrical specifications Figure 11. Distortion vs. output power Figure 13. Supply voltage rejection vs. voltage gain Figure 15. Power dissipation and efficiency vs. output power (R 10/19 Figure 12. Distortion vs. frequency Figure 14. Supply voltage rejection vs. Figure 16. ...
Page 11
TDA2003A Figure 17. Maximum power dissipation vs. supply voltage (sine wave operation) Figure 19. Typical values of capacitor (C different values of frequency response (B) Figure 18. Maximum allowable power dissipation vs. ambient temperature ) for X Doc ID 018796 ...
Page 12
Application information 3 Application information Figure 20. Typical application circuit Figure 21. Printed circuit board and component layout for typical application circuit 3.1 Built-in protection systems 3.1.1 Load dump voltage surge The TDA2003A has a circuit which enables it to ...
Page 13
TDA2003A Figure 22. Voltage gain bridge configuration Figure 23. Suggested LC network circuit 3.1.2 Short-circuit (AC and DC conditions) The TDA2003A can withstand a permanent short-circuit on the output for a supply voltage 3.1.3 Polarity inversion ...
Page 14
Application information 3.1.7 Thermal shutdown The presence of a thermal limiting circuit offers the following advantages overload on the output (even permanent excessive ambient temperature can be easily withstood. 2. The heatsink can ...
Page 15
TDA2003A 3.2.3 Application recommendations The recommended component values are those shown in the application circuit in Figure 20. Different values can be used. The following table is intended to aid the car-radio designer. Table 5. Recommended values of the components ...
Page 16
Package information 4 Package information In order to meet environmental requirements, ST offers these devices in different grades of ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ...
Page 17
TDA2003A Figure 27. Pentawatt (horizontal) mechanical data and package dimensions DIM. MIN 2.40 D1 1.20 E 0.35 F 0.80 F1 1.00 G 3. 10.05 L 14.20 L1 5.70 L2 14.60 L3 3.50 L4 ...
Page 18
Revision history 5 Revision history Table 6. Document revision history Date 02-May-2011 14-Jun-2011 18/19 Revision 1 Initial release. Removed minimum value from Pentawatt (vertical) package 2 dimension H3 (Figure Doc ID 018796 Rev 2 Changes 26). TDA2003A ...
Page 19
... TDA2003A Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...