SI3016-F-FS Silicon Laboratories Inc, SI3016-F-FS Datasheet - Page 7

• Manufacturer Part Number: SI3016-F-FS
• Description: IC ISOMODEM LINE-SIDE DAA 16SOIC
• Manufacturer: Silicon Laboratories Inc
• Type: Chipsetr

Specifications of SI3016-F-FS

• Package / Case: 16-SOIC (3.9mm Width)
• Data Format: V.90
• Baud Rates: 56k
• Interface: Serial
• Voltage - Supply: 3.3V, 5V
• Mounting Type: Surface Mount
• Product: Modem Chip
• Supply Current: 0.3 mA
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 4. AC Characteristics (Continued)
(T
Parameter
Caller ID Full Scale Level (0 dB gain)
Caller ID Full Scale Level (ARX = 00)
Gain Accuracy
Gain Accuracy
Notes:
Table 5. Absolute Maximum Ratings
Table 6. Digital FIR Filter Characteristics—Transmit and Receive
(Sample Rate
Parameter
Operating Temperature Range
Storage Temperature Range
Note: Permanent device damage may occur if the absolute maximum ratings are exceeded. Functional operation should be
Parameter
Passband (0.1 dB)
Passband (3 dB)
Passband Ripple Peak-to-Peak
Stopband
Stopband Attenuation
Group Delay
Note: Typical FIR filter characteristics for Fs
A
=
1. Measured at TIP and RING with 600 Ω termination at 1 kHz, as shown in Figure 1.
2. R2 should be changed to a 243 Ω resistor when the FULLSCALE bit (FULL) is set to 1 (Register 18, bit 7).
3. Receive full scale level will produce –0.9 dBFS at SDO.
4. DR
5. Measurement is 300 to 3400 Hz. Applies to both transmit and receive paths.
6. Vin
7. Vin
8. THD
9. The AOUT pin is an optional pin located on the integrated system-side module. V
0 to 70 °C for K-Grade and –40 to 85 °C for B-Grade; see Figure 6 on page 9)
the integrated system-side module.
restricted to the conditions as specified in the operational sections of this data sheet. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
=
=
=
=
20 x log |Vin| + 20 x log (RMS signal/RMS noise).
1 kHz, –3 dBFS, Fs
1 KHz, –6 dBFS, Fs
=
20 x log (RMS distortion/RMS signal).
5,6
5,6
8 kHz, T
A
=
70 °C for K-Grade and –40 to 85 °C for B-Grade)
=
=
10300 Hz.
10300 Hz.
Symbol
=
V
V
8000 Hz are shown in Figures 2, 3, 4, and 5.
CID
CID
Symbol
F
F
(0.1 dB)
(3 dB)
t
gd
Symbol
ARX = 000, 001, or 010
T
2-W to SDO, ATX and
2-W to SDO, ATX and
Rev. 1.0
T
STG
A
Test Condition
ARX = 011, 1xx
MODE = 0
MODE = 1
–0.1
Min
–74
—
—
0
0
–40 to 100
–65 to 150
12/Fs
Value
Typ
4.4
—
—
—
—
D
–0.5
Min
–1
refers to the digital power supply of
—
—
Typ
Max
0.8
1.4
3.3
3.6
0.1
0
0
—
—
—
Si3016
Max
0.5
—
—
Unit
1
°C
°C
Unit
kHz
kHz
kHz
sec
dB
dB
Unit
V
V
dB
dB
PP
PP
7