MCP23017-E/ML Microchip Technology, MCP23017-E/ML Datasheet - Page 6

• Manufacturer Part Number: MCP23017-E/ML
• Description: IC I/O EXPANDER I2C 16B 28QFN
• Manufacturer: Microchip Technology

Specifications of MCP23017-E/ML

• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Interface: I²C
• Number Of I /o: 16
• Interrupt Output: Yes
• Frequency - Clock: 1.7MHz
• Voltage - Supply: 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Logic Family: MCP23017
• Propagation Delay Time: 50 ns
• Operating Supply Voltage: 1.8 V to 5.5 V
• Power Dissipation: 700 mW
• Operating Temperature Range: - 40 C to + 125 C
• Input Voltage: 1.8 V to 5.5 V
• Logic Type: I/O Expander
• Maximum Clock Frequency: 10 MHz
• Maximum Operating Frequency: 1.7 MHz
• Mounting Style: SMD/SMT
• Output Current: 25 mA
• Output Voltage: 1.8 V to 4.5 V
• Package: 28QFN EP
• Chip Configuration: 16 Bit
• Bus Frequency: 1.7MHz
• Ic Interface Type: I2C
• No. Of I/o's: 16
• Supply Voltage Range: 1.8V To 5.5V
• Digital Ic Case Style: QFN
• No. Of Pins: 28
• Interface Type: I2C
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP23X17EV - BOARD EVAL FOR MCP23X17GPIODM-KPLCD - BOARD DEMO LCD GPIO EXP KEYPAD
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

MCP23017/MCP23S17
1.3.2.2
I
as shown in the bottom of
followed by another control byte (including the Start
condition and ACK) with the R/W bit set (R/W = 1). The
MCP23017 then transmits the data contained in the
addressed register. The sequence is ended with the
master generating a Stop or Restart condition.
1.3.2.3
For sequential operations (Write or Read), instead of
transmitting a Stop or Restart condition after the data
transfer, the master clocks the next byte pointed to by
the address pointer (see Section 1.3.1 “Byte Mode
and Sequential Mode” for details regarding sequential
operation control).
The sequence ends with the master sending a Stop or
Restart condition.
The MCP23017 Address Pointer will roll over to
address zero after reaching the last register address.
Refer to
DS21952B-page 6
2
C Read operations include the control byte sequence,
Figure
I
I
2
2
C Read Operation
C Sequential Write/Read
1-1.
Figure
1-1. This sequence is
1.3.3
1.3.3.1
The SPI write operation is started by lowering CS. The
Write command (slave address with R/W bit cleared) is
then clocked into the device. The opcode is followed by
an address and at least one data byte.
1.3.3.2
The SPI read operation is started by lowering CS. The
SPI read command (slave address with R/W bit set) is
then clocked into the device. The opcode is followed by
an address, with at least one data byte being clocked
out of the device.
1.3.3.3
For sequential operations, instead of deselecting the
device by raising CS, the master clocks the next byte
pointed to by the Address Pointer. (see Section 1.3.1
“Byte Mode and Sequential Mode” for details
regarding sequential operation control).
The sequence ends by the raising of CS.
The MCP23S17 Address Pointer will roll over to
address zero after reaching the last register address.
SPI INTERFACE
SPI Write Operation
SPI Read Operation
SPI Sequential Write/Read
© 2007 Microchip Technology Inc.