KSZ8001L Micrel Inc, KSZ8001L Datasheet - Page 32

• Manufacturer Part Number: KSZ8001L
• Description: IC TXRX PHY 10/100 3.3V 48-LQFP
• Manufacturer: Micrel Inc
• Type: Transceiverr

Specifications of KSZ8001L

• Protocol: MII, RMII, SMII
• Voltage - Supply: 1.8V, 3.3V
• Mounting Type: Surface Mount
• Package / Case: 48-LQFP
• Data Rate: 100Mbps
• No. Of Ports: 1
• Ethernet Type: IEEE 802.3u
• Supply Current: 52mA
• Supply Voltage Range: 1.71V To 1.89V, 3.135V To 3.465V
• Operating Temperature Range: 0°C To +70°C
• Digital Ic Case: RoHS Compliant
• Interface Type: MII, RMII
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 576-1620 - BOARD EVALUATION FOR KSZ8001L
• Number Of Drivers/receivers: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 576-1508; 576-1508-5; 576-1508-5; KSZ8001L

March 2006
Micrel
Address
1f:14
1f:13
1f.12
1f.11
1f.10
1f.9
1f.8
1f.7
1f.6
1f.5
1f.4:2
1f.1
1f.0
Name
MDI/MDI-X
Select
Pairswap
disable
Energy detect
Force link
Power Saving
Interrupt Level
Enable Jabber
Auto-
Negotiation
Complete
Enable Pause
(Flow-Control
Result)
PHY Isolate
Operation
Mode
Indication
Enable SQE
test
Disable Data
Scrambling
Description
When Auto MDI/MDI-X is disabled,
0 =
1 =
1 = disable MDI/MDIX
0 = enable MDI/MDIX
1 = presence of signal on RX+/- analog wire
pair
0 = no signal detected on RX+/-
1 = force link pass
0 = normal link operation
This bit bypasses the control logic and allow
transmitter to send pattern even if there is no
link.
1 = enable power saving
0 = disable
1 = interrupt pin active high
0 = active low
1 = enable jabber counter
0 = disable
1 = auto-negotiation complete
0 = not complete
This bit has the same definition as register 1.5.
1 = flow control capable
0 = no flow control
1 = PHY in isolate mode
0 = not isolated
[000] = still in auto-negotiation
[001] = 10BASE-T half duplex
[010] = 100BASE-TX half duplex
[011] = default
[101] = 10BASE-T full duplex
[110] = 100BASE-TX full duplex
[111] = PHY/MII isolate
1 = enable SQE test
0 = disable
1 = disable scrambler
0 = enable
Transmit on TX+/- (pins 41,40)
Receive on RX+/- (pins 33,32)
Transmit on RX+/- (pins 33,32)
Receive on TX+/- (pins 41,40)
32
Mode
RW
RW
RO
RW
RW
RW
RW
RO
RO
RO
RO
RW
RW
Default
0
0
0
0
1
0
1
0
0
0
0
0
0
Revision 1.03
KSZ8001