20-101-1132 Rabbit Semiconductor, 20-101-1132 Datasheet - Page 109

• Manufacturer Part Number: 20-101-1132
• Description: MODULE RCM4210 RABBITCORE
• Manufacturer: Rabbit Semiconductor

Specifications of 20-101-1132

• Module/board Type: MPU Core Module
• Product: Microcontroller Modules
• Core Processor: Rabbit 4000
• Flash: 512 KBytes
• Operating Supply Voltage: 3 to 3.6 V
• Board Size: 61 mm x 47 mm x 21 mm
• Cpu Core: Rabbit 4000
• For Use With/related Products: RCM4210
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 316-1125

B.1.1 Prototyping Board Features
•
•
•
•
•
•
•
•
User’s Manual
Power Connection
Note that the 3-pin header is symmetrical, with both outer pins connected to ground and
the center pin connected to the raw V+ input. The cable of the AC adapter provided
with the North American version of the Development Kit is terminated with a header
plug that connects to the 3-pin header in either orientation. The header plug leading to
bare leads provided for overseas customers can be connected to the 3-pin header in
either orientation.
Users providing their own power supply should ensure that it delivers 8–24 V DC at
8 W. The voltage regulators will get warm while in use.
Regulated Power Supply
routed to a 5 V switching voltage regulator, then to a separate 3.3 V linear regulator.
The regulators provide stable power to the RCM4200 module and the Prototyping
Board.
Power LED
Board.
Reset Switch
RCM4200’s
I/O Switches and LEDs
nected to the PB4 and PB5 pins of the RCM4200 module and may be read as inputs by
sample applications.
Two LEDs are connected to the PB2 and PB3 pins of the RCM4200 module, and may
be driven as output indicators by sample applications.
Prototyping Area
of through-hole components. +3.3 V, +5 V, and Ground buses run around the edge of
this area. Several areas for surface-mount devices are also available. (Note that there
are SMT device pads on both top and bottom of the Prototyping Board.) Each SMT pad
is connected to a hole designed to accept a 30 AWG solid wire.
Module Extension Header
duplicated at header J2. Developers can solder wires directly into the appropriate holes,
or, for more flexible development, a 2 × 25 header strip with a 0.1" pitch can be sol-
dered into place. See Figure B-4 for the header pinouts.
Analog Inputs Header
header J3. These analog signals are connected via attenuator/filter circuits on the Proto-
typing Board to the corresponding analog inputs on the RCM4200 module. Developers
can solder wires directly into the appropriate holes, or, for more flexible development, a
2 × 7 header strip with a 0.1" pitch can be soldered into place. See Figure B-4 for the
header pinouts.
NOTE: The same Prototyping Board can be used for several series of RabbitCore mod-
ules, and so the signals at J2 depend on the signals available on the specific RabbitCore
module.
—The power LED lights whenever power is connected to the Prototyping
/RESET_IN
—A momentary-contact, normally open switch is connected directly to the
—A generous prototyping area has been provided for the installation
—A a 3-pin header is provided for connection to the power supply.
—The Prototyping Board’s analog signals are presented at
pin. Pressing the switch forces a hardware reset of the system.
—Two momentary-contact, normally open switches are con-
—The raw DC voltage provided at the 3-pin header is
—The complete pin set of the RCM4200 module is
103