ADSP-21061KS-133 Analog Devices Inc, ADSP-21061KS-133 Datasheet - Page 26

• Manufacturer Part Number: ADSP-21061KS-133
• Description: IC DSP CONTROLLER 32BIT 240MQFP
• Manufacturer: Analog Devices Inc
• Series: SHARC®r
• Type: Floating Pointr

Specifications of ADSP-21061KS-133

• Rohs Status: RoHS non-compliant
• Interface: Synchronous Serial Port (SSP)
• Clock Rate: 33MHz
• Non-volatile Memory: External
• On-chip Ram: 128kB
• Voltage - I/o: 5.00V
• Voltage - Core: 5.00V
• Operating Temperature: 0°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 240-MQFP, 240-PQFP
• Frequency: 33MHz
• Supply Voltage: 5V
• Embedded Interface Type: HPI, Serial
• No. Of Mips: 50
• Supply Voltage Range: 4.75V To 5.25V
• Operating Temperature Range: 0°C To +85°C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

ADSP-21061/ADSP-21061L
Memory Write—Bus Master
Use these specifications for asynchronous interfacing to memo-
ries (and memory-mapped peripherals) without reference to
CLKIN. These specifications apply when the ADSP-21061 is the
Table 13. Memory Write—Bus Master
1
2
3
Parameter
Timing Requirements
t
t
Switching Characteristics
t
t
t
t
t
t
t
t
t
t
W = (number of wait states specified in WAIT register) × t
H = t
I = t
ACK delay/setup: User must meet t
The falling edge of MSx, SW, BMS is referenced.
For more information, see
DAAK
DSAK
DAWH
DAWL
WW
DDWH
DWHA
DATRWH
WWR
DDWR
WDE
SADADC
(high).
CK
CK
(if a bus idle cycle occurs, as specified in WAIT register; otherwise I = 0).
(if an address hold cycle occurs, as specified in WAIT register; otherwise H = 0).
ACK Delay from Address, Selects
ACK Delay from WR Low
Address, Selects to WR Deasserted
Address, Selects to WR Low
WR Pulse Width
Data Setup Before WR High
Address Hold After WR Deasserted
Data Disable After WR Deasserted
WR High to WR, RD, DMAGx Low
Data Disable Before WR or RD Low
WR Low to Data Enabled
Address, Selects to ADRCLK High
ADDRESS
RD, DMAG
MSX, SW
ADRCLK
BMS
(OUT)
DATA
ACK
WR
Example System Hold Time Calculation on Page 44
DAAK
or t
1
t
SADADC
DSAK
t
DAWL
2
or synchronous specification t
t
DAAK
1, 2
2
3
2
t
Figure 15. Memory Write—Bus Master
DSAK
Rev. C | Page 26 of 56 | July 2007
t
WDE
CK
.
t
DAWH
for calculation of hold times given capacitive and dc loads.
SAKC
for deassertion of ACK (low), all three specifications must be met for assertion of ACK
t
WW
bus master accessing external memory space in asynchronous
access mode. Note that timing for ACK, DATA, RD, WR, and
DMAGx strobe timing parameters only applies to asynchronous
access mode.
Min
17 + 15DT/16 + W
3 + 3DT/8
13 + 9DT/16 + W
7 + DT/2 + W
1 + DT/16 + H
1 + DT/16 +H
8 + 7DT/16 + H
5 + 3DT/8 + I
–1 + DT/16
0 + DT/4
t
DDWH
5 V and 3.3 V
t
DATRWH
t
DWHA
Max
15 + 7DT/8 + W
8 + DT/2 + W
6 + DT/16+H
t
WWR
t
DDWR
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns