LQ070Y3DG3A Sharp Electronics, LQ070Y3DG3A Datasheet

Page 1

... Technical Document LCD Specification LCD Group LQ070Y3DG3A LCD Module Product Specification February 2009 WVGA Module featuring LED backlight, 16:9 aspect ratio, excellent color rendition, 350 nits brightness, and 300:1 contrast. Full Specifications Listing ...

Page 2

...

Page 3

... LQ070Y3DG3A ^SPEC No. DATE LD-21212A Feb.17.2009 RECORDS OF REVISION REVISED No. PAGE - - SUMMARY NOTE st 1 Issue ...

Page 4

These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for ...

Page 5

Table of contents 1. Application ..............................................................................3 2. Overview ................................................................................3 3. Mechanical Specifications ...................................................................3 4. Input Terminals ...........................................................................4 4-1. TFT-LCD panel driving .................................................................4 4-2. LED- Backlight driving .................................................................4 5. Absolute Maximum Ratings .................................................................5 6. Electrical Characteristics ....................................................................5 6-1.TFT-LCD panel driving .................................................................5 ...

Page 6

... Application This specification applies to a color TFT-LCD module, LQ070Y3DG3A. 2. Overview This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor composed of a color TFT-LCD panel, driver ICs, power supply circuit, and a backlight unit. Graphics and texts can be displayed on a 800× ...

Page 7

Input Terminals 4-1. TFT-LCD panel driving CN1(Timing signals,DATA signals and +3.3V DC power supply) Pin No. Symbol GND 1 GND 2 VCC +3.3V Power Supply 3 VCC +3.3V Power Supply 4 R0 RED data signal(LSB ...

Page 8

Absolute Maximum Ratings Parameter Input voltage +3.3V supply voltage LED forward current LED reverse voltage Storage temperature Operating temperature [Note 1] R0-7、G0-7、B0-7、DOTCLK、HSYNC、VSYNC、DEN [Note 2] LED_A to LED_Cn (n=1,2,3) Absolute maximum ratings for each pair. [Note 3] Humidity：95%RH Max. at ...

Page 9

Symbol for the power sequence for backlight recommended to apply above mentioned input timing. If the backlight is lit on and off at a timing other than shown ...

Page 10

Backlight driving The backlight system is edge-lighting type with 24 White-LED(White Light Emitting Diode). The characteristics of White-LED are shown in the following table. Parameter Symbol LED voltage LED current range Number of circuit strings LED power consumption LED ...

Page 11

Display position Characteristics DEN Setup time Pulse width Phase difference of HSYNC - DEN [Note] (Horizontal display direction) When “DEN” signal is fixed low, 216 clocks are counted from Hsync negative edge and data from after are available. If ...

Page 12

THp Horizontal sync. signal (Hsync) THc Only when “DEN” terminal is fix ed "L ow" Clock signal (DOTCLK) C1* C215* C216* ...

Page 13

Input Signals, Basic Display Colors and Gray Scale of Each Color Colors & Gray Gray scale Scale Black − Blue − Green − Cyan ...

Page 14

Optical Characteristics Parameter Symbol Horizontal θ21,θ22 Viewing θ11 angle range Vertical θ12 Contrast ratio CRn Response time τr+τd x Chromaticity of white y x Chromaticity of red y x Chromaticity of green y x Chromaticity of blue y Luminance ...

Page 15

Definitions of viewing angle range: [Note 4] Definition of contrast ratio: The contrast ratio is defined as the following. Contrast Ratio (CR) ＝ [Note 5] Definition of response time: The response time is defined as the following figure ...

Page 16

Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable. Please insert for too much stress not to join FFC/FPC in the case of insertion of FFC/FPC sure to design ...

Page 17

Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you intend to install a fan. r) Epoxy resin (amine series curing agent), silicone adhesive material (dealcoholization series and oxime series), tray forming agent (azo ...

Page 18

Label 1) Module label: Notation: ① Model No. ② Serial No. Ｌ Ｑ ０ ７ ０ Ｙ ３ Ｄ Ｇ ３ Ａ Details of Serial No ９ ２ ０ ０ ０ ０ ０ １ (Example) Production year(9∼) Production Month(1∼9,X,Y,Z) ...

Page 19

Storage conditions <Environmental condition range of storage temperature and humidity> Temperature degrees Celsius Relative humidity 70% and below Direct sun light Please keep the product in a dark room or cover the product to protect from ...

Page 20

Fig 2. Packing form LD21212A-17 ...

Page 21

Fig 3. Outline dimensions LD21212A-18 ...

Page 22

... MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED event will SHARP be liable, or responsible in any way, for any incidental or consequential economic or property damage. LD-20706A EUROPE Sharp Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com SINGAPORE Sharp Electronics (Singapore) PTE ...