ISL22326WFV14Z Intersil, ISL22326WFV14Z Datasheet
ISL22326WFV14Z
Specifications of ISL22326WFV14Z
Available stocks
Related parts for ISL22326WFV14Z
ISL22326WFV14Z Summary of contents
Page 1
... PART MARKING ISL22326UFV14Z* 22326 UFVZ ISL22326UFR16Z* 223 26UFZ ISL22326WFV14Z* 22326 WFVZ ISL22326WFR16Z* 223 26WFZ *Add “-TK” suffix for tape and reel. Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations) ...
Page 2
... EPAD* *Note: PCB thermal land for QFN EPAD should be connected to GND plane or left floating. For more information refer to http://www.intersil.com/data/tb/TB389.pdf 2 ISL22326 V CC POWER-UP INTERFACE CONTROL AND STATUS LOGIC NON- VOLATILE REGISTERS GND PIN NAME V Power supply pin CC SHDN Shutdown active low input RH0 “ ...
Page 3
... Thermal Resistance (Typical, Notes 1, 2) θ 14 Lead TSSOP . . . . . . . . . . . . . . . . . . + 0 Lead QFN . . . . . . . . . . . . . . . . . . . . Maximum Junction Temperature (Plastic Package +150°C Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . .see link below CC http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Temperature Range (Extended Industrial .-40°C to +125° 2.7V to 5.5V CC Power Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15mW Wiper Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±3.0mA ...
Page 4
Analog Specifications Over recommended operating conditions, unless otherwise stated. (Continued) SYMBOL PARAMETER RESISTOR MODE (Measurements between R RINL Integral Non-linearity (Note 15) RDNL Differential Non-linearity (Note 14) Roffset Offset (Note 13) R DCP to DCP Matching MATCH (Note 16) Operating ...
Page 5
Operating Specifications Over the recommended operating conditions, unless otherwise specified. (Continued) SYMBOL PARAMETER t Power-up Delay D EEPROM SPECIFICATION EEPROM Endurance EEPROM Retention t Non-volatile Write Cycle Time WC (Note 18) SERIAL INTERFACE SPECIFICATIONS V A2, A1, A0, SHDN, SDA, ...
Page 6
Operating Specifications Over the recommended operating conditions, unless otherwise specified. (Continued) SYMBOL PARAMETER Rpu SDA and SCL Bus Pull-up Resistor Off-chip t A2, A1 and A0 Setup Time SU:A t A2, A1 and A0 Hold Time HD:A NOTES: 4. Typical ...
Page 7
SDA vs SCL Timing SCL t SU:STA t HD:STA SDA (INPUT TIMING) SDA (OUTPUT TIMING) A0, A1, and A2 Pin Timing START SCL SDA A0, A1 Typical Performance Curves 100 V = 3.3V +125°C CC ...
Page 8
Typical Performance Curves 0 2.7V CC 0 5. TAP POSITION (DECIMAL) FIGURE 3. DNL vs TAP POSITION IN VOLTAGE DIVIDER MODE FOR 10kΩ (W) 1.3 10k 1.1 0.9 ...
Page 9
Typical Performance Curves 1.0 0 2. 5.5V CC 10k -0.5 -1.0 -40 - TEMPERATURE (ºC) FIGURE 9. END TO END R % CHANGE vs TOTAL TEMPERATURE 300 250 200 150 50k ...
Page 10
Pin Descriptions Potentiometers Pins RHI AND RLI ( The high (RHi) and low (RLi) terminals of the ISL22326 are equivalent to the fixed terminals of a mechanical potentiometer. RHi and RLi are referenced to the relative position ...
Page 11
TABLE 1. MEMORY MAP ADDRESS NON-VOLATILE 8 — 7 Reserved 6 General Purpose 5 General Purpose 4 General Purpose 3 General Purpose 2 General Purpose 1 IVR1 0 IVR0 The non-volatile IVRi and volatile WRi registers are accessible with the ...
Page 12
SCL SDA START FIGURE 16. VALID DATA CHANGES, START AND STOP CONDITIONS SCL FROM MASTER SDA OUTPUT FROM TRANSMITTER HIGH IMPEDANCE SDA OUTPUT FROM RECEIVER START FIGURE 17. ACKNOWLEDGE RESPONSE FROM RECEIVER SIGNALS FROM THE MASTER SIGNAL AT SDA SIGNALS ...
Page 13
Write Operation A Write operation requires a START condition, followed by a valid Identification Byte, a valid Address Byte, a Data Byte, and a STOP condition. After each of the three bytes, the ISL22326 responds with an ACK. At this ...
Page 14
... Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. 9. Features and dimensions A2, A3, D1, E1, P & θ are present when Anvil singulation method is used and not present for saw singulation ...
Page 15
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...