MPC9608AC Freescale Semiconductor, MPC9608AC Datasheet - Page 7

• Manufacturer Part Number: MPC9608AC
• Description: IC CLOCK BUFFER 1:10 32-LQFP
• Manufacturer: Freescale Semiconductor
• Type: Fanout Distribution, Multiplexer , Zero Delay Bufferr

Specifications of MPC9608AC

• Pll: Yes with Bypass
• Input: LVCMOS
• Output: LVCMOS
• Number Of Circuits: 1
• Ratio - Input:output: 1:10
• Differential - Input:output: No/No
• Frequency - Max: 200MHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 3.135 V ~ 3.465 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 32-LQFP
• Frequency-max: 200MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Advanced Clock Drivers Device Data
Freescale Semiconductor
is specified. I/O jitter numbers for other confidence factors
(CF) can be derived from
layout and can be used to fine-tune the effective delay
through each device. In the following example calculation a
I/O jitter confidence factor of 99.7% (± 3σ) is assumed,
resulting in a worst case timing uncertainty from input to any
output of -295 ps to 295 ps
t
t
Driving Transmission Lines
speed signals in a terminated transmission line environment.
To provide the optimum flexibility to the user the output driv-
ers were designed to exhibit the lowest impedance possible.
With an output impedance of less than 20 Ω the drivers can
drive either parallel or series terminated transmission lines.
For more information on transmission lines the reader is re-
ferred to Freescale Semiconductor application note AN1091.
In most high performance clock networks point-to-point distri-
bution of signals is the method of choice. In a point-to-point
scheme either series terminated or parallel terminated trans-
mission lines can be used. The parallel technique terminates
the signal at the end of the line with a 50 Ω resistance to
V
thus only a single terminated line can be driven by each
output of the MPC9608 clock driver. For the series terminated
case however there is no DC current draw, thus the outputs
can drive multiple series terminated lines.
an output driving a single series terminated line versus two
series terminated lines in parallel. When taken to its extreme,
the fanout of the MPC9608 clock driver is effectively doubled
due to its capability to drive multiple lines.
1. Skew data are designed targets and pending device specifications.
SK(PP)
SK(PP)
Table 8. Confidence Factor CF
CC
Due to the statistical nature of I/O jitter, an RMS value (1 σ)
The feedback trace delay is determined by the board
This technique draws a fairly high level of DC current and
± 1σ
± 2σ
± 3σ
± 4σ
± 5σ
± 6σ
CF
The MPC9608 clock driver was designed to drive high
÷ 2.
= [-100 ps...100 ps] + [-150 ps...150 ps] +
= [-295 ps...295 ps] + t
[(15 ps
Probability of clock edge within the distribution
.
-3)...(15 ps
Table
(1)
relative to CCLK:
0.68268948
0.95449988
0.99730007
0.99993663
0.99999943
0.99999999
.
PD, LINE(FB)
3)] + t
8.
PD, LINE(FB)
Figure 5
illustrates
Waveforms
single line versus two lines. In both cases the drive capability
of the MPC9608 output buffer is more than sufficient to drive
50 Ω transmission lines on the incident edge. From the delay
measurements in the simulations a delta of only 43 ps exists
between the two differently loaded outputs. This suggests
that the dual line driving need not be used exclusively to
maintain the tight output-to-output skew of the MPC9608.
The output waveform in
Waveforms
caused by the impedance mismatch seen looking into the
driver. The parallel combination of the 36 Ω series resistor
plus the output impedance does not match the parallel
combination of the line impedances. The voltage wave
launched down the two lines will equal:
near unity reflection coefficient. It will then increment towards
the quiescent 3.0 V in steps separated by one round trip delay
(in this case 4.0 ns).
IN
IN
At the load end the voltage will double to 2.6 V due to the
The waveform plots in
Figure 5. Single versus Dual Transmission Lines
MPC9608
MPC9608
14 Ω
Output
14 Ω
Output
Buffer
Buffer
show the simulation results of an output driving a
shows a step in the waveform. This step is
V
Z
R
R
V
0
L
L
S
0
= V
= 50 Ω || 50 Ω
= 36 Ω || 36 Ω
= 14 Ω
= 3.0 (25 ÷ (18 + 17 + 25))
= 1.31 V
S
(Z
Figure 6. Single versus Dual
R
R
R
0
S
S
S
Figure 6. Single versus Dual
÷ (R
= 36 Ω
= 36 Ω
= 36 Ω
S
+ R
Z
Z
Z
0
O
O
O
+ Z
= 50 Ω
= 50 Ω
= 50 Ω
0
))
MPC9608
OutA
OutB0
OutB1
7