5962-8766105XA E2V, 5962-8766105XA Datasheet - Page 2

• Manufacturer Part Number: 5962-8766105XA
• Manufacturer: E2V

Specifications of 5962-8766105XA

• Lead Free Status / RoHS Status: Supplier Unconfirmed

DSCC FORM 2234
APR 97
accordance with MIL-PRF-38535, appendix A.
1/ Lid shall be transparent to permit ultraviolet light erasure.
2/ Under absolute maximum ratings, voltages are with respect to GND.
3/ Maximum junction temperature may be increased to +175C during burn-in and steady-state life.
4/ V
5/ V
1.4 Recommended operating conditions.
1.3 Absolute maximum ratings.
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
not be inserted into or removed from the board when V
During programming, V
CC
PP
Outline letter
can be connected to V
must be applied before or at the same time as V
Device type
Supply voltage range (V
Supply voltage range (V
All input voltage range except A
Input voltage range (A
Output voltage range 2/ ..............................................................
Storage temperature range ........................................................
Power dissipation ........................................................................
Lead temperature (soldering, 10 seconds) ..................................
Thermal resistance, junction-to-case (θ
Junction temperature (T
Data retention ............................................................................
Supply voltage range (V
Supply voltage range (V
High level input voltage range (V
High level input voltage range (V
Low level input voltage range (V
Low level input voltage range (V
Case operating temperature range (T
DEFENSE SUPPLY CENTER COLUMBUS
Drawing number
Y
X
5962-87661
MICROCIRCUIT DRAWING
01
02
03
04
05
06
07
08
COLUMBUS, OHIO 43218-3990
STANDARD
PP
must be maintained at 12.5 V (±0.5 V).
Generic number 1/
CC
9
) 2/ ..........................................................
CC
PP
J
CC
PP
GDIP1-T28 or CDIP2-T28
directly (except in the program mode). V
) ..........................................................
Device type
27C128
27C128
27C128
27C128
27C128
27C128
27C128
27C128
Descriptive designator
(see 1.2.1)
) 2/ .....................................................
) 5/ .....................................................
) 2/ .....................................................
) 4/ ....................................................
2/
01
CQCC1-N32
9
IL
IL
IH
IH
) .............................................
) .............................................
2/ ..........................................
)..............................................
)..............................................
C
) ......................................
JC
) ...................................
Case outline
16K x 8-bit UVEPROM
16K x 8-bit UVEPROM
16K x 8-bit UVEPROM
16K x 8-bit UVEPROM
16K x 8-bit UVEPROM
16K x 8-bit UVEPROM
16K x 8-bit UVEPROM
16K x 8-bit UVEPROM
(see 1.2.2)
PP
Circuit function
PP
and removed after or at the same time as V
X
or V
CC
is applied.
SIZE
A
Terminals
CC
28
32
Lead finish
(see 1.2.3)
supply current in this case would be I
2.0 V dc to 6.5 V dc (TTL)
-0.6 V dc to 6.25 V dc
-0.6 V dc to 14.0 V dc
-0.6 V dc to 6.25 V dc
-0.6 V dc to 13.5 V dc
-0.6 V dc to V
-65C to +150C
300 mW
+300C
See MIL-STD-1835
+150C 3/
10 years minimum
4.5 V dc to 5.5 V dc
4.5 V dc to 5.5 V dc
V
-0.1 V dc to 0.8 V dc (TTL)
GND -0.2 to GND +0.2 V dc (CMOS)
-55C to +125C
CC
A
-0.2 V dc to V
REVISION LEVEL
CC
Access time
dual-in-line package
rectangular leadless chip carrier
+ 1.0 V dc
G
120 ns
150 ns
170 ns
200 ns
250 ns
300 ns
CC
90 ns
70 ns
+0.2 V dc (CMOS)
Package style 1/
PP
. The device must
SHEET
5962-87661
CC
+ I
PP
.
2