TJA1053T NXP Semiconductors, TJA1053T Datasheet
TJA1053T
Specifications of TJA1053T
Available stocks
Related parts for TJA1053T
TJA1053T Summary of contents
Page 1
DATA SHEET TJA1053 Fault-tolerant CAN transceiver Product specification Supersedes data of 1997 Oct 15 File under Integrated Circuits, IC18 INTEGRATED CIRCUITS 2000 Dec 18 ...
Page 2
Philips Semiconductors Fault-tolerant CAN transceiver FEATURES Optimized for in-car low-speed communication Baud rate up to 125 kbaud nodes can be connected Supports unshielded bus wires Low RFI due to built-in slope control function Fully integrated receiver filters ...
Page 3
... Philips Semiconductors Fault-tolerant CAN transceiver ORDERING INFORMATION TYPE NUMBER NAME TJA1053T SO14 BLOCK DIAGRAM handbook, full pagewidth 1 INH 7 WAKE 5 STB TXD TIMER 4 NERR 3 RXD 13 GND 2000 Dec 18 PACKAGE DESCRIPTION plastic small outline package; 14 leads; body width 3.9 mm BAT 14 TEMPERATURE WAKE-UP PROTECTION ...
Page 4
... HIGH in dominant state CANL 12 low voltage bus line, will be LOW in dominant state GND 13 ground BAT 14 battery voltage 2000 Dec 18 handbook, halfpage INH 1 TXD 2 RXD 3 TJA1053T 4 NERR STB WAKE MGL182 Fig.2 Pin configuration. 4 Product specification TJA1053 14 BAT 13 GND 12 CANL 11 ...
Page 5
Philips Semiconductors Fault-tolerant CAN transceiver FUNCTIONAL DESCRIPTION The TJA1053 is the interface between the CAN protocol controller and the physical bus primarily intended for low speed applications 125 kbaud, in passenger cars. The device provides differential ...
Page 6
Philips Semiconductors Fault-tolerant CAN transceiver Wake-up requests are recognized by the transceiver when a dominant signal is detected on either bus line or if the WAKE pin is connected to ground wake-up request the transceiver will set the ...
Page 7
Philips Semiconductors Fault-tolerant CAN transceiver LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL PARAMETER V supply voltage input voltage at pins input voltage at pins 11 ...
Page 8
Philips Semiconductors Fault-tolerant CAN transceiver CHARACTERISTICS V = 4. STB CC ground; positive currents flow into the IC; all parameters are guaranteed over the temperature range by design, but only 100% tested at ...
Page 9
Philips Semiconductors Fault-tolerant CAN transceiver SYMBOL PARAMETER Pin INH V HIGH-level voltage drop dropH I leakage current LI Pins CANH and CANL V differential receiver threshold drx voltage V CANH recessive output voltage oCANHrec V CANL recessive output voltage oCANLrec ...
Page 10
Philips Semiconductors Fault-tolerant CAN transceiver SYMBOL PARAMETER Pins RTH and RTL R RTL to V switch-on resistance RTL CC RTL to V switch series BAT resistance R RTH to ground switch-on RTH resistance V RTH output voltage oRTH I RTL ...
Page 11
Philips Semiconductors Fault-tolerant CAN transceiver SYMBOL PARAMETER t propagation delay TXD-to-RXD PD(H) HIGH t minimum dominant time for wu(min) wake-up on CANL or CANH t minimum WAKE LOW time for WAKE(min) wake-up t failure 3 detection time fail failure 6 ...
Page 12
Philips Semiconductors Fault-tolerant CAN transceiver TEST AND APPLICATION INFORMATION 5 V ndbook, full pagewidth 20 pF (1) Termination resistors R1 (100 ) are not connected to RTH or RTL for testing purposes because the minimum load resistance allowed on the ...
Page 13
Philips Semiconductors Fault-tolerant CAN transceiver handbook, full pagewidth WAKE handbook, full pagewidth The waveforms of applied transients shall be in accordance with “ ISO7637, part 1 ”, test pulses and 3b. 2000 Dec ...
Page 14
Philips Semiconductors Fault-tolerant CAN transceiver PACKAGE OUTLINE SO14: plastic small outline package; 14 leads; body width 3 pin 1 index 1 e DIMENSIONS (inch dimensions are derived from the original mm dimensions) A UNIT A A ...
Page 15
Philips Semiconductors Fault-tolerant CAN transceiver SOLDERING Introduction to soldering surface mount packages This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “Data Handbook IC26; Integrated Circuit ...
Page 16
Philips Semiconductors Fault-tolerant CAN transceiver Suitability of surface mount IC packages for wave and reflow soldering methods PACKAGE BGA, HBGA, LFBGA, SQFP, TFBGA HBCC, HLQFP, HSQFP, HSOP, HTQFP, HTSSOP, HVQFN, SMS (3) PLCC , SO, SOJ LQFP, QFP, TQFP SSOP, ...
Page 17
Philips Semiconductors Fault-tolerant CAN transceiver DATA SHEET STATUS PRODUCT DATA SHEET STATUS STATUS Objective specification Development Preliminary specification Qualification Product specification Production Note 1. Please consult the most recently issued data sheet before initiating or completing a design. DEFINITIONS Short-form ...
Page 18
Philips Semiconductors Fault-tolerant CAN transceiver 2000 Dec 18 NOTES 18 Product specification TJA1053 ...
Page 19
Philips Semiconductors Fault-tolerant CAN transceiver 2000 Dec 18 NOTES 19 Product specification TJA1053 ...
Page 20
Philips Semiconductors – a worldwide company Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. + 101 ...