MAX2395EGI-T Maxim Integrated Products, MAX2395EGI-T Datasheet
MAX2395EGI-T
Specifications of MAX2395EGI-T
Related parts for MAX2395EGI-T
MAX2395EGI-T Summary of contents
Page 1
... Single-Supply Operation o +6dBm Output Power at 72mA o 81dB Minimum Automatic Gain-Control (AGC) Range o Automatic I Consumption SAW Filter Necessary o On-Chip RF PLL, with Fully Monolithic VCO o Ultra-Low External Component Count PART Applications MAX2395EGI MAX2395ETI MAX2395ETI Exposed pad. + Denotes a lead(Pb)-free/RoHS-compliant package GND_VCO V VCO ...
Page 2
WCDMA Quasi-Direct Modulator with VGA and PA Driver ABSOLUTE MAXIMUM RATINGS V to GND ...........................................................-0.3V to +3.6V CC All Other Pins to GND..................................-0. I_, Q_, REF to GND..............................................................1V Digital Input Current .........................................................±10mA Stresses beyond those listed under “Absolute ...
Page 3
AC ELECTRICAL CHARACTERISTICS MAX2395 EV kit +2.7V to +3.3V +85°C. I/Q inputs driven differentially with low- impedance source based on 3GPP UpLink reference measurement channel (12.2kbps), envelope level 1V . Typical values are at V P-P ...
Page 4
WCDMA Quasi-Direct Modulator with VGA and PA Driver AC ELECTRICAL CHARACTERISTICS (continued) MAX2395 EV kit +2.7V to +3.3V +85°C. I/Q inputs driven differentially with low- impedance source based on 3GPP UpLink reference measurement channel (12.2kbps), envelope ...
Page 5
MPL = 1, and EVM vs. P OUT -40° +25° +85° -30 -26 -22 -18 ...
Page 6
WCDMA Quasi-Direct Modulator with VGA and PA Driver PIN NAME 1 N.C. Connect to RF GND on PCB Transmitter Output. This is an open-collector output and requires a pullup inductor to the supply 2 POUT voltage. This pullup inductor can ...
Page 7
PIN NAME Supply for VCO. Bypass to system ground with a capacitor as close to the pin as possible. Do not 20 V _VCO CC share ground vias for the bypass capacitor with any other branch (see the Typical Operating ...
Page 8
... In idle mode, the VCO, PLL, and serial interface remain on to minimize startup time. The GmC filter can be software programmed to power on or off during idle mode (see Table 5). Idle Mode is a trademark of Maxim Integrated Products, Inc. 8 _______________________________________________________________________________________ The Tx outputs are internally matched to 50Ω. The ...
Page 9
Table 2. Register Power-Up Default States (f REGISTER RFM RFR OPCTRL Table 3. Operation Control Register (OPCTRL) Bit Assignments BIT NAME POWER-UP STATE SHDN 1 IDLE_PRG 0 — 1 GmC_EN 1 PLL_EN 1 VCO_EN 1 PA_RF_IF_EN 1 X2_EN 0 MPL ...
Page 10
WCDMA Quasi-Direct Modulator with VGA and PA Driver Table 4. Reference-Divider (RFR) Register BIT NAME POWER-UP STATE RFR8 to RFR0 001010000 LD1, LD0 0 0 RCPT2, RCPT1 RCPT0 RESERVED 1 RESERVED 0 Table 5. Power-Down Modes POWER-DOWN ...
Page 11
BIT 15 BIT 14 SDATA SCLK Figure 1. 3-Wire SPI/MICROWIRE Serial-Interface Timing Diagram MSB B15 B14 B13 B12 B11 B10 B15 B14 B13 B12 B11 B10 B15 B14 B13 B12 B11 B10 OPERATION CONTROL REGISTER (16 BITS) ...
Page 12
WCDMA Quasi-Direct Modulator with VGA and PA Driver V CC N.C. 1 POWER AMPLIFIER POUT 2 V _PA CC 3 BIAS_SET 4 VGC 5 V _IF _BB ______________________________________________________________________________________ ...
Page 13
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13 © 2009 Maxim Integrated Products ...