ATA5811-PLQW80 Atmel, ATA5811-PLQW80 Datasheet - Page 63

• Manufacturer Part Number: ATA5811-PLQW80
• Description: RF Transceiver RF Data Control Transceiver
• Manufacturer: Atmel

Specifications of ATA5811-PLQW80

• Wireless Frequency: 226 KHz
• Interface Type: 4-Wire SPI
• Noise Figure: 7 dB
• Output Power: 10 dBm
• Operating Supply Voltage: 2.4 V to 5.25 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Package / Case: QFN-48
• Maximum Data Rate: 20 Kbps
• Minimum Operating Temperature: - 40 C
• Modulation: ASK, FSK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12. Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
13. Thermal Resistance
14. Electrical Characteristics: General
All parameters refer to GND and are valid for T
6.6V (2-battery application) and V
T
pin properties can be found in the specific sections of the “Electrical Characteristics”.
4689F–RKE–08/06
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
amb
Parameters
Junction temperature
Storage temperature
Ambient temperature
Supply voltage VS2
Supply voltage VS1
Supply voltage VAUX
Supply voltage VSINT
ESD (Human Body Model ESD S 5.1)
every pin
ESD (Machine Model JEDEC A115A)
every pin
Maximum input level, input matched to 50
Parameters
Junction ambient
No. Parameters
1.1
1.2
1
= 25°C, f
RX_TX_IDLE Mode
RF operating frequency
range
Supply current
OFF mode
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50
component values according to
with component values according to
RF
= 433.92 MHz (1-battery application) unless otherwise specified. Details about current consumption, timing and digital
VS2
Test Conditions
ATA5811
V
ATA5811
V
ATA5812
V
V
V
(1 battery) and
V
OFF mode is not
available if
V
V
433_N868
433_N868
433_N868
VS1
VSINT
VS2
VSINT
VS2
= V
= V
= 6 V (2 battery)
= V
VAUX
= 0 V
= 0 V (car)
VS2
= 0 V
= AVCC
= 0 V
VAUX
Table 5-2 on page 10
= 4.75V to 5.25V (car application). Typical values are given at V
= 3 V,
amb
= 5 V
Table 5-7 on page
= –40°C to +105°C, V
V
V
Symbol
Symbol
V
V
P
MaxVSINT
MaxVAUX
HBM
R
T
MaxVS2
MaxVS1
MM
T
in_max
T
amb
thJA
stg
Pin
4, 10
4, 10
4, 10
j
(1)
and RF_OUT matched to 50
20.
Symbol
VS1
I
S_OFF
f
f
f
RF
RF
RF
= V
VS2
–200
Min.
–0.3
–0.3
–0.3
–0.3
–55
–40
–2
= 2.4V to 3.6V (1-battery application), V
Min.
867
433
313
Value
25
according to
ATA5811/ATA5812
according to
Typ.
<10
Max.
+125
+105
+200
+7.2
+7.2
+5.5
150
+4
+2
10
Figure 5-1 on page 10
VS1
Max.
Figure 5-10 on page 19
870
435
316
= V
VS2
= 3V and
Unit
MHz
MHz
MHz
nA
VS2
Unit
dBm
Unit
K/W
kV
°C
°C
°C
V
V
V
V
V
= 4.4V to
Type*
with
A
A
A
A
63