LAN9215I-MT SMSC, LAN9215I-MT Datasheet - Page 30

• Manufacturer Part Number: LAN9215I-MT
• Description: Ethernet ICs Indust Hi Efficient Single-Chip
• Manufacturer: SMSC
• Type: Single Chip MAC and PHY Controllerr

Specifications of LAN9215I-MT

• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Product: Ethernet Controllers
• Number Of Transceivers: 1
• Standard Supported: 802.3, 802.3u
• Data Rate: 10 Mbps, 100 Mbps
• Supply Voltage (max): 5 V
• Supply Voltage (min): 3.3 V
• Supply Current (max): 69 mA
• Maximum Operating Temperature: + 85 C
• Package / Case: TQFP-100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Revision 2.7 (03-15-10)
3.6
3.6.1
3.6.2
3.6.3
3.6.4
Destination Address Source Address ……………FF FF FF FF FF FF
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
…CRC
It should be noted that Magic Packet detection can be performed when LAN9215i is in the D0 or D1
power states. In the D0 state, “Magic Packet” detection is enabled when the MPEN bit is set. In the
D1 state, Magic Packet detection, as well as wake-up frame detection, are automatically enabled when
the device enters the D1 state.
Bus Writes
The host processor is required to perform two contiguous 16-bit writes to complete a single DWORD
transfer. This DWORD must begin and end on a DWORD address boundary (A[2] and higher, cannot
change during a sixteen bit write). No ordering requirements exist. The processor can access either
the low or high word first, as long as the next write is performed to the other word. If a write to the
same word is performed, the LAN9215i disregards the transfer.
Bus Reads
The host processor is required to perform two consecutive 16-bit reads to complete a single DWORD
transfer. This DWORD must begin and end on a DWORD address boundary (A[2] and higher, cannot
change during a sixteen bit read). No ordering requirements exist. The processor can access either
the low or high word first, as long as the next read is performed from the other word. If a read to the
same word is performed, the data read is invalid and should be re-read. This is not a fatal error. The
LAN9215i will reset its read counters and restart a new cycle on the next read.
Big and Little Endian Support
The LAN9215i supports “Big-” or “Little-Endian” processors with either 16 or 32-bit busses. To support
big-endian processors, the hardware designer must explicitly invert the layout of the byte lanes.
Word Swap Function
Internally the LAN9215i is 32-bits wide. The LAN9215i supports a Word Swap Function. This feature
is controlled by the Word Swap Register, which is described in
Swap Control," on page
the Control and Status Registers and the Transmit and Receive Data/Status FIFOs. Refer to
"Word Swap Control"
Data FIFO to the network, the low order word is always transmitted first, and when the LAN9215i
receives data from the network to the Receive Data FIFO, the low-order word is always received first.
Host Bus Operations
below for more details. Whenever the LAN9215i transmits data from the Transmit
90. This register affects how words on the data bus are written to or read from
DATASHEET
16-bit Non-PCI 10/100 Ethernet Controller with HP Auto-MDIX and Industrial Temperature Support
30
Section 5.3.17, "WORD_SWAP—Word
SMSC LAN9215i
Table 3.7,
Datasheet