ACPL-5630L-300 Avago Technologies US Inc., ACPL-5630L-300 Datasheet - Page 8

• Manufacturer Part Number: ACPL-5630L-300
• Description: Hermetic Optocoupler
• Manufacturer: Avago Technologies US Inc.

Specifications of ACPL-5630L-300

• Voltage - Isolation: 1500VDC
• Number Of Channels: 2, Unidirectional
• Current - Output / Channel: 25mA
• Data Rate: 10MBd
• Propagation Delay High - Low @ If: 54ns @ 13mA
• Current - Dc Forward (if): 20mA
• Input Type: DC
• Output Type: Open Collector
• Mounting Type: Surface Mount
• Package / Case: 8-SMD Gull Wing
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Notes:
1. Each channel.
2. All devices are considered two-terminal devices; I
3. Measured between each input pair shorted together and all output connections for that channel shorted together.
4. Measured between adjacent input pairs shorted together for each multichannel device.
5. t
6. CM
7. This is a momentary withstand test, not an operating condition.
8. It is essential that a bypass capacitor (0.01 to 0.1 µF, ceramic) be connected from V
9. No external pull up is required for a high logic state on the enable input.
10. The t
11. The t
12. Standard commercial parts receive 100% testing at 25°C (Subgroups 1 and 9). Class H and K parts receive 100% testing at 25, 125, and
13. Parameters are tested as part of device initial characterization and after design and process changes. Parameters are guaranteed to limits
Figure 1. High Level Output Current vs. Tempera-
ture.
8
100
leads or terminals shorted together.
the output pulse. The t
on the trailing edge of the output pulse.
(V
high state (V
this external capacitor and the isolator connections should not exceed 20 mm.
the trailing edge of the output pulse.
the leading edge of the output pulse.
-55°C (Subgroups 1 and 9, 2 and 10, 3 and 11, respectively).
specified for all lots not specifically tested.
80
60
40
20
PHL
0
-60 -40 -20 0
O
< 0.8 V). CM
propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.5 V point on the leading edge of
L
is the maximum rate of rise of the common mode voltage that can be sustained with the output voltage in the logic low state
ELH
EHL
enable propagation delay is measured from the 1.5 V point on the trailing edge of the enable input pulse to the 1.5 V point on
enable propagation delay is measured from the 1.5 V point on the leading edge of the enable input pulse to the 1.5 V point on
T
A
O
> 2.0 V).
- TEMPERATURE - °C
H
20 40 60 80 100 120 140
is the maximum rate of fall of the common mode voltage that can be sustained with the output voltage in the logic
PLH
propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.5 V point
V
V
I
F
CC
O
= 250 µA
= 3.3 V
= 3.3 V
Figure 2. Input-Output Characteristics.
5
4
3
2
1
0
1
I-O
is measured between all input leads or terminals shorted together and all output
I
F
2
- INPUT DIODE FORWARD CURRENT - mA
3
4
510
1
4
R
L
kΩ
kΩ
Ω
5
V
T
A
CC
= 25 °C
= 3.3 V
6
CC
7
to ground. Total lead length between both ends of
Figure 3. Input Diode Forward Characteristics.