ISL29028IROZ-T7 Intersil, ISL29028IROZ-T7 Datasheet
ISL29028IROZ-T7
Specifications of ISL29028IROZ-T7
Available stocks
Related parts for ISL29028IROZ-T7
ISL29028IROZ-T7 Summary of contents
Page 1
... Industrial and Medical Light and Proximity Sensing CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. | 1-888-INTERSIL or 1-888-468-3774 Intersil (and design registered trademark of Intersil Americas Inc Bus is a registered trademark owned by NXP Semiconductors Netherlands, B.V. All other trademarks mentioned are the property of their respective owners. ...
Page 2
... Ordering Information PART NUMBER (Notes 1, 2) ISL29028IROZ-T7 NOTES: 1. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations ...
Page 3
... A Thermal Resistance (Typical, Note ODFN Maximum Die Temperature . . . . . . . . . . . . . . . . . . . +90°C Storage Temperature . . . . . . . . . . . . . . . . -40°C to +100°C Operating Temperature . . . . . . . . . . . . . . . -40°C to +85°C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp = 3.0V +25° 499kΩ 1% tolerance EXT V Rising Edge between 0.4V and 2.25V DD ALS_EN = 0 ...
Page 4
Electrical Specifications V PARAMETER DESCRIPTION V Acceptable Voltage Range on IRDR Pin IRDR t Net I On Time Per PROX Reading PULSE IRDR V Voltage of R Pin REF EXT Clock Rate Range I C ...
Page 5
I2C Electrical Specifications PARAMETER DESCRIPTION t Bus Free Time Between a STOP and START BUF Condition C Capacitive Load for Each Bus Line b R SDA and SCL system bus pull-up resistor pull-up t Data Valid Time VD;DAT t Data ...
Page 6
Register Map There are ten 8-bit registers accessible via I Registers 0x3 through 0x7 store the various ALS/IR/Prox thresholds which trigger interrupt events. Registers 0x8 through 0xA store the results of ALS/IR/Prox ADC conversions. TABLE 1. ISL29028 REGISTERS AND REGISTER ...
Page 7
TABLE 4. REGISTER 0x02 (INTERRUPT) - PROX/ALS INTERRUPT CONTROL BIT # ACCESS DEFAULT BIT NAME PROX_FLAG 7 FLAG 0x00 (Prox Flag) PROX_PRST 6:5 RW 0x00 (Prox Persist) Unused 4 RW 0x00 (Write 0) ALS_FLAG 3 FLAG 0x00 (ALS FLAG) ALS_PRST ...
Page 8
TABLE 10. REGISTER 0x08 (PROX_DATA) - PROXIMITY SENSOR DATA BIT # ACCESS DEFAULT 7:0 RO 0x00 TABLE 11. REGISTER 0x09 (ALSIR_DT1) - ALS/IR SENSOR DATA (LOWER 8 BITS) BIT # ACCESS DEFAULT 7:0 RO 0x00 TABLE 12. REGISTER 0x0A (ALSIR_DT2) ...
Page 9
ALS ACTIVE PROX SENSOR ACTIVE IRDR (CURRENT DRIVER) FIGURE 3. TIMING DIAGRAM FOR PROX/ALS EVENTS - NOT TO SCALE The proximity sensor is an 8-bit ADC which operates in a similar fashion. When proximity sensing is enabled, the IRDR pin ...
Page 10
... Upon power-up, please ensure a V 0.5V/ms or greater. After power-up the user’s power supply temporarily deviates from our specification (2.25V to 3.63V), Intersil recommends the user write 0x00 to three registers: 0x0E, 0x0F, and 0x01 (in that order), wait ~1ms or more and then rewrite all registers to the desired values ...
Page 11
... Suggested PCB Footprint It is important that users check the “Surface Mount Assembly Guidelines for Optical Dual FlatPack No Lead (ODFN) Package” before starting ODFN product board mounting. (http://www.intersil.com/data/tb/TB477.pdf SLAVE_0 1 ADDR0 IRDR 2 VDD C1 C2 1µF 0.1µF 3 GND SDA 4 REXT REXT ISL29028 499kΩ ...
Page 12
Typical Performance Curves 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -90 -60 -30 0 ANGULAR OFFSET (°) FIGURE 8. ANGULAR SENSITIVITY 300 18% GREY CARD 250 220mA MODE 200 110mA MODE 150 100 WHITE COPY PAPER ...
Page 13
Typical Performance Curves FIGURE 14. STABILITY OF ALS COUNT OVER-TEMPERATURE (AT 0.00 LUX) 2.00 0.43 FIGURE 15 ODFN SENSOR LOCATION OUTLINE - DIMENSIONS ISL29028 V = 3.0V EXT ...
Page 14
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries ...
Page 15
Package Outline Drawing L8.2.1x2.0 8 LEAD OPTICAL DUAL FLAT NO-LEAD PLASTIC PACKAGE (ODFN) Rev 1, 12/09 2.10 6 PIN 1 INDEX AREA (2X) 0.10 TOP VIEW 2.50 2.10 (6x0.50) (8x0.20) (8x0.55) (0.75) TYPICAL RECOMMENDED LAND PATTERN 15 ISL29028 A B ...