PIC18F46K20-E/P Microchip Technology, PIC18F46K20-E/P Datasheet - Page 3
![IC, 8BIT MCU, PIC18F, 64MHZ, DIP-40](/photos/6/61/66192/150-40-dip_sml.jpg)
PIC18F46K20-E/P
Manufacturer Part Number
PIC18F46K20-E/P
Description
IC, 8BIT MCU, PIC18F, 64MHZ, DIP-40
Manufacturer
Microchip Technology
Series
PIC® XLP™ 18Fr
Datasheets
1.PIC18F25K20T-ISS.pdf
(42 pages)
2.PIC18F25K20T-ISS.pdf
(456 pages)
3.PIC18F26K20-ISS.pdf
(6 pages)
4.PIC18F26K20-ISS.pdf
(10 pages)
Specifications of PIC18F46K20-E/P
Controller Family/series
PIC18
No. Of I/o's
36
Eeprom Memory Size
1024Byte
Ram Memory Size
3936Byte
Cpu Speed
64MHz
No. Of Timers
4
Core Size
8 Bit
Program Memory Size
32768 Words
Core Processor
PIC
Speed
48MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
35
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
3.8K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Data Converters
A/D 14x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
40-DIP (0.600", 15.24mm)
Processor Series
PIC18F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
3936 B
Interface Type
CCP, ECCP, EUSART, I2C, MSSP, SPI
Maximum Clock Frequency
64 MHz
Number Of Programmable I/os
36
Number Of Timers
4
Maximum Operating Temperature
+ 125 C
Mounting Style
Through Hole
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DV164136
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 14 Channel
Package
40PDIP
Device Core
PIC
Family Name
PIC18
Maximum Speed
64 MHz
Operating Supply Voltage
2.5|3.3 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC164112 - VOLTAGE LIMITER MPLAB ICD2 VPPDM164124 - KIT STARTER FOR PIC18F4XK20
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18F46K20-E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Silicon Errata Issues
1. Module: ECCP
2. Module: ECCP
2010 Microchip Technology Inc.
Note:
Changing direction in Full-Bridge mode inserts a
dead band time of 4/F
instead of 1/F
the data sheet.
Work around
None.
Affected Silicon Revisions
ECCP
PR2 = CCPR1L and DC1B[1:0] <>'00' and the
direction is changed, then the dead time before the
modulated output starts is compromised. The
modulated signal improperly starts immediately
with the direction change and stays on for
T
Work around
Avoid changing direction when the duty cycle is
within three least significant steps of 100% duty
cycle. Instead, clear the DC1B[1:0] bits before the
direction change and then set them to the desired
value after the direction change is complete.
Affected Silicon Revisions
OSC
B2
B2
X
X
* TMR2Presale * DC1B[1:0].
This document summarizes all silicon
errata issues from all revisions of silicon,
previous as well as current. Only the
issues indicated by the shaded column in
the following tables apply to the current
silicon revision (B5).
B3
B3
X
X
–
OSC
B5
B5
X
X
In
* TMR2 prescale as specified in
Full-Bridge
OSC
* TMR2 prescale
mode
when
3. Module: MSSP SPI
4. Module: MSSP SPI
5. Module: MSSP (Master I
PIC18F26K20/46K20
When the SPI clock is configured for Timer2/2
(SSPCON1<3:0> = 0011) and the CKE bit of the
SSPSTAT register is ‘1’, then the first SDO data bit
and SCK non-idle edge occur simultaneously.
Also, the first SCK non-idle level may be short.
Work around
Use clock mode other than Timer2/2.
Affected Silicon Revisions
In SPI Master mode, when the CKE bit of the
SSPSTAT register is cleared and the SMP bit of
the SSPSTAT register is set, then the last bit of the
incoming data stream (bit 0) at the SDI pin will not
be sampled properly.
Work around
None.
Affected Silicon Revisions
In Master I
occurs in the middle of an address or data
reception, then the SCL clock stream will continue
endlessly and the RCEN bit of the SSPCON2
register will remain set improperly. When a Start
condition occurs after the improper Stop condition,
then 9 additional clocks will be generated followed
by the RCEN bit going low.
Work around
Use low-impedance pull-ups on the SDA line to
reduce the possibility of noise glitches, which may
trigger an improper Stop event. Use a time-out
event timer to detect the unexpected Stop condi-
tion and resulting stuck RCEN bit. Clear stuck
RCEN bit by clearing SSPEN bit of SSPCON1.
Affected Silicon Revisions
B2
B2
B2
X
X
X
B3
B3
B3
X
X
X
2
C Receive mode, if a Stop condition
B5
B5
B5
X
X
X
2
C™ Mode)
DS80404E-page 3