DSPIC30F4012-20I/SO Microchip Technology, DSPIC30F4012-20I/SO Datasheet - Page 187

• Manufacturer Part Number: DSPIC30F4012-20I/SO
• Description: IC, DSC, 16BIT, 48KB 20MHZ, 5.5V, SOIC28
• Manufacturer: Microchip Technology
• Series: DsPIC30Fr

Specifications of DSPIC30F4012-20I/SO

• Core Frequency: 20MHz
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of I/o's: 20
• Flash Memory Size: 48KB
• Supply Voltage Range: 2.5V To 5.5V
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 20
• Program Memory Size: 48KB (16K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Package: 28SOIC W
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 20
• Interface Type: CAN/I2C/SPI/UART
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28SO-1 - SOCKET TRANSITION 28SOIC 300MIL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: DSPIC30F401220ISO

TABLE 24-13: EXTERNAL CLOCK TIMING REQUIREMENTS
© 2010 Microchip Technology Inc.
AC CHARACTERISTICS
OS10
OS20
OS25
OS30
OS31
OS40
OS41
Note 1:
Param
No.
2:
3:
4:
F
T
T
TosL,
TosH
TosR,
TosF
TckR
TckF
Symbol
OSC
CY
OSC
Data in “Typ” column is at 5V, 25°C unless otherwise stated. Parameters are for design guidance only and
are not tested.
These parameters are characterized but not tested in manufacturing.
Instruction cycle period (T
are based on characterization data for that particular oscillator type under standard operating conditions
with the device executing code. Exceeding these specified limits may result in an unstable oscillator
operation and/or higher than expected current consumption. All devices are tested to operate at “min.”
values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the
“Max.” cycle time limit is “DC” (no clock) for all devices.
Measurements are taken in EC or ERC modes. The CLKO signal is measured on the OSC2 pin. CLKO is
low for the Q1-Q2 period (1/2 T
External CLKI Frequency
(external clocks allowed only
in EC mode)
Oscillator Frequency
T
Instruction Cycle Time
External Clock in (OSC1)
High or Low Time
External Clock in (OSC1)
Rise or Fall Time
CLKO Rise Time
CLKO Fall Time
OSC
= 1/F
Characteristic
OSC
(2)
(2,4)
(2,4)
(2)
CY
(2)
) equals four times the input oscillator time base period. All specified values
(2)
(2,3)
CY
) and high for the Q3-Q4 period (1/2 T
.45 x T
Standard Operating Conditions: 2.5V to 5.5V
(unless otherwise stated)
Operating temperature
Min
DC
DC
0.4
10
31
33
—
—
—
—
—
—
4
4
4
4
4
4
4
OSC
Typ
7.37
512
dsPIC30F4011/4012
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
(1)
Max
-40°C ≤ T
-40°C ≤ T
DC
7.5
7.5
40
10
10
10
10
10
25
33
—
—
—
—
20
—
—
4
4
CY
A
A
Units
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
).
kHz
kHz
ns
ns
ns
ns
ns
≤ +85°C for Industrial
≤ +125°C for Extended
—
EC
EC with 4x PLL
EC with 8x PLL
EC with 16x PLL
RC
XTL
XT
XT with 4x PLL
XT with 8x PLL
XT with 16x PLL
HS
LP
FRC internal
LPRC internal
See parameter OS10
for F
See
EC
EC
See parameter
See parameter
OSC
Table 24-16
DS70135G-page 187
Conditions
value
DO31
DO32