A24-HABUF-P5I Digi International/Maxstream, A24-HABUF-P5I Datasheet - Page 33

• Manufacturer Part Number: A24-HABUF-P5I
• Description: 2.4GHZ ANTENNA U.FL
• Manufacturer: Digi International/Maxstream

Specifications of A24-HABUF-P5I

• Antenna Type: Whip
• Number Of Bands: 1
• Frequency: 2.4GHz
• Gain: 2.1dBi
• Termination: U.FL
• Mounting Type: Bulkhead
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Vswr: -
• Height (max): -
• Other names: A24-HABUF-P51; A24-HABUF-P51; Q3655966F

Table 3‐06. XBee‐PRO Commands ‐ I/O Settings (sub‐category designated within {brackets})
* Firmware version in which the command was first introduced (firmware versions are numbered in hexadecimal notation.)
Diagnostics
Table 3‐07. XBee®/XBee‐PRO® Commands ‐ Diagnostics
XBee®/XBee‐PRO® RF Modules ‐ 802.15.4 ‐ v1.xEx [2009.09.23]
AT
Command
D5 (v1.x80*)
D0 - D4
(v1.xA0*)
IU (v1.xA0*)
IT (v1.xA0*)
IS (v1.xA0*)
IO (v1.xA0*)
IC (v1.xA0*)
IR (v1.xA0*)
IA (v1.xA0*)
T0 - T7
(v1.xA0*)
P0
P1 (v1.xA0*)
M0 (v1.xA0*)
M1 (v1.xA0*)
PT (v1.xA0*)
RP
AT
Command
VR
VL (v1.x80*)
Command
Category
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
Command
Category
Diagnostics
Diagnostics
Name and Description
DIO5 Configuration. Configure settings for the DIO5 line (pin 15) of the RF module.
Options include Associated LED indicator (blinks when associated) and I/O line
settings.
(DIO4 -DIO4) Configuration. Select/Read settings for the following lines: AD0/DIO0
(pin 20), AD1/DIO1 (pin 19), AD2/DIO2 (pin 18), AD3/DIO3 (pin 17), AD4/DIO4 (pin 11).
Options include: Analog-to-digital converter, Digital Input and Digital Output.
I/O Output Enable. Disables/Enables I/O data received to be sent out UART. The data
is sent using an API frame regardless of the current AP parameter value.
Samples before TX. Set/Read the number of samples to collect before transmitting
data. Maximum number of samples is dependent upon the number of enabled inputs.
Force Sample. Force a read of all enabled inputs (DI or ADC). Data is returned through
the UART. If no inputs are defined (DI or ADC), this command will return error.
Digital Output Level. Set digital output level to allow DIO lines that are setup as
outputs to be changed through Command Mode.
DIO Change Detect. Set/Read bitfield values for change detect monitoring. Each bit
enables monitoring of DIO0 - DIO7 for changes. If detected, data is transmitted with
DIO data only. Any samples queued waiting for transmission will be sent first.
Sample Rate. Set/Read sample rate. When set, this parameter causes the module to
sample all enabled inputs at a specified interval.
I/O Input Address. Set/Read addresses of module to which outputs are bound. Setting
all bytes to 0xFF will not allow any received I/O packet to change outputs. Setting
address to 0xFFFF will allow any received I/O packet to change outputs.
(D0 - D7) Output Timeout. Set/Read Output timeout values for lines that correspond
with the D0 - D7 parameters. When output is set (due to I/O line passing) to a non-
default level, a timer is started which when expired will set the output to it default level.
The timer is reset when a valid I/O packet is received.
PWM0 Configuration. Select/Read function for PWM0 pin.
PWM1 Configuration. Select/Read function for PWM1 pin.
PWM0 Output Level. Set/Read the PWM0 output level.
PWM1 Output Level. Set/Read the PWM1 output level.
PWM Output Timeout. Set/Read output timeout value for both PWM outputs. When
PWM is set to a non-zero value: Due to I/O line passing, a time is started which when
expired will set the PWM output to zero. The timer is reset when a valid I/O packet is
received.]
RSSI PWM Timer. Set/Read PWM timer register. Set the duration of PWM (pulse width
modulation) signal output on the RSSI pin. The signal duty cycle is updated with each
received packet and is shut off when the timer expires.]
Name and Description
Firmware Version. Read firmware version of the RF module.
Firmware Version - Verbose. Read detailed version information (including application
build date, MAC, PHY and bootloader versions). The VL command has been
deprecated in version 10C9. It is not supported in firmware versions after 10C8
© 2009 Digi Internatonal, Inc.
Parameter Range
0 - 1
0 - 1
0 - 1
1 - 0xFF
8-bit bitmap (each bit
represents the level of an I/O
line setup as an output)
-
0 - 0xFF [bitfield]
0 - 0xFFFF [x 1 msec]
0 - 0xFFFFFFFFFFFFFFFF
0 - 0xFF [x 100 ms]
0 - 2
0 - 2
0 - 0x03FF
0 - 0x03FF
0 - 0xFF [x 100 ms]
0 - 0xFF [x 100 ms]
Parameter Range
0 - 0xFFFF [read-only]
-
0 = Disabled
1 = Associated indicator
2 = ADC
3 = DI
4 = DO low
5 = DO high
0 = Disabled
1 = (n/a)
2 = ADC
3 = DI
4 = DO low
5 = DO high
0 = Disabled
1 = Enabled
0 = Disabled
1 = RSSI
2 = PWM Output
0 = Disabled
1 = RSSI
2 = PWM Output
Default
1
0
1
1
-
-
0 (disabled)
0
0xFFFFFFF
FFFFFFFFF
0xFF
1
0
-
-
0xFF
0x28 (40d)
Default
Factory-set
-
33