C8051F017-GQ Silicon Laboratories Inc, C8051F017-GQ Datasheet - Page 109

• Manufacturer Part Number: C8051F017-GQ
• Description: IC 8051 MCU 32K FLASH 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F01xr

Specifications of C8051F017-GQ

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 32-LQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 8
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 4x10b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 8
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F005DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• On-chip Dac: 2-ch x 12-bit
• No. Of I/o's: 8
• Ram Memory Size: 256Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• No. Of Pwm Channels: 5
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1196

15.3.
Each MCU has four byte-wide, bi-directional parallel ports that can be used general purpose I/O. Each port is
accessed through a corresponding special function register (SFR) that is both byte addressable and bit addressable.
When writing to a port, the value written to the SFR is latched to maintain the output data value at each pin. When
reading, the logic levels of the port’s input pins are returned regardless of the XBRn settings (i.e. even when the pin
is assigned to another signal by the Crossbar, the Port Register can always still read its corresponding Port I/O pin).
The exception to this is the execution of the read-modify-write instructions. The read-modify-write instructions
when operating on a port SFR are the following: ANL, ORL, XRL, JBC, CPL, INC, DEC, DJNZ and MOV, CLR
or SET, when the destination is an individual bit in a port SFR. For these instructions, the value of the port register
(not the pin) is read, modified, and written back to the SFR.
15.4.
P2 and P3 are not pinned out on the F001/06/11/16. P1, P2, and P3 are not pinned out on the F002/07/12/17. These
port registers (and corresponding interrupts, where applicable) are still available for software use in these reduced
pin count MCUs. Whether used or not in software, it is recommended not to let these port drivers go to high
impedance state. This is prevented after reset by having the weak pull-ups enabled as described in the XBR2
register. It is recommended that each output driver for ports not pinned out should be configured as push-pull using
the corresponding PRTnCF register. This will inhibit a high impedance state even if the weak pull-up is disabled.
109
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Bits7-0: P0.[7:0]
Bits7-0: PRT0CF.[7:0]: Output Configuration Bits for P0.7-P0.0 (respectively)
P0.7
R/W
R/W
Bit7
Bit7
General Purpose Port I/O
Configuring Ports Which are not Pinned Out
(Write – Output appears on I/O pins per XBR0, XBR1, and XBR2 Registers)
0: Logic Low Output.
1: Logic High Output (high-impedance if corresponding PRT0CF.n bit = 0)
(Read – Regardless of XBR0, XBR1, and XBR2 Register settings).
0: P0.n pin is logic low.
1: P0.n pin is logic high.
0: Corresponding P0.n Output mode is Open-Drain.
1: Corresponding P0.n Output mode is Push-Pull.
(Note: When SDA, SCL, and RX appear on any of the P0 I/O, each are open-drain
P0.6
R/W
R/W
Bit6
Bit6
regardless of the value of PRT0CF).
Figure 15.7. PRT0CF: Port0 Configuration Register
P0.5
R/W
R/W
Bit5
Bit5
Figure 15.6. P0: Port0 Register
P0.4
R/W
R/W
Bit4
Bit4
Rev. 1.7
P0.3
R/W
R/W
Bit3
Bit3
P0.2
R/W
R/W
Bit2
Bit2
P0.1
R/W
R/W
Bit1
Bit1
(bit addressable)
P0.0
R/W
R/W
Bit0
Bit0
0x80
SFR Address:
SFR Address:
Reset Value
Reset Value
11111111
00000000
0xA4