ATMEGA8535-16PU Atmel, ATMEGA8535-16PU Datasheet - Page 77

• Manufacturer Part Number: ATMEGA8535-16PU
• Description: IC AVR MCU 8K 16MHZ 5V 40DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8535-16PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• A/d Inputs: 8-Channel, 10-Bit
• Cpu Speed: 16 MIPS
• Eeprom Memory: 512 Bytes
• Input Output: 32
• Interface: SPI/TWI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 40-pin PDIP
• Programmable Memory: 8K Bytes
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 4.5-5.5 V
• Controller Family/series: AVR MEGA
• No. Of I/o's: 32
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 512Byte
• Rohs Compliant: Yes
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2502G–AVR–04/05
Figure 32. Fast PWM Mode, Timing Diagram
The Timer/Counter Overflow Flag (TOV0) is set each time the counter reaches MAX. If
the interrupt is enabled, the interrupt handler routine can be used for updating the com-
pare value.
In fast PWM mode, the compare unit allows generation of PWM waveforms on the OC0
pin. Setting the COM01:0 bits to two will produce a non-inverted PWM and an inverted
PWM output can be generated by setting the COM01:0 to three (See Table 41 on page
83). The actual OC0 value will only be visible on the port pin if the data direction for the
port pin is set as output. The PWM waveform is generated by setting (or clearing) the
OC0 Register at the Compare Match between OCR0 and TCNT0, and clearing (or set-
ting) the OC0 Register at the timer clock cycle the counter is cleared (changes from
MAX to BOTTOM).
The PWM frequency for the output can be calculated by the following equation:
The “N” variable represents the prescale factor (1, 8, 64, 256, or 1024).
The extreme values for the OCR0 Register represents special cases when generating a
PWM waveform output in the fast PWM mode. If the OCR0 is set equal to BOTTOM, the
output will be a narrow spike for each MAX+1 timer clock cycle. Setting the OCR0 equal
to MAX will result in a constantly high or low output (depending on the polarity of the out-
put set by the COM01:0 bits).
A frequency (with 50% duty cycle) waveform output in fast PWM mode can be achieved
by setting OC0 to toggle its logical level on each Compare Match (COM01:0 = 1). The
waveform generated will have a maximum frequency of f
set to zero. This feature is similar to the OC0 toggle in CTC mode, except the double
buffer feature of the output compare unit is enabled in the fast PWM mode.
TCNTn
Period
OCn
OCn
1
2
3
f
OCnPWM
4
=
----------------- -
N 256
f
clk_I/O
⋅
5
ATmega8535(L)
OC0
6
= f
clk_I/O
OCRn Interrupt Flag Set
OCRn Update and
TOVn Interrupt Flag Set
7
/2 when OCR0 is
(COMn1:0 = 2)
(COMn1:0 = 3)
77