ATTINY44A-CCUR Atmel, ATTINY44A-CCUR Datasheet - Page 112

• Manufacturer Part Number: ATTINY44A-CCUR
• Description: MCU AVR 4KB FLASH 20MHZ 15UFBGA
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY44A-CCUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 12
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.11.9
112
ATtiny24A/44A/84A
TIFR1 – Timer/Counter Interrupt Flag Register 1
• Bits 7:6 – Res: Reserved Bits
These bits are reserved bits in the ATtiny24A/44A/84A and will always read as zero.
• Bit 5 – ICF1: Timer/Counter1, Input Capture Flag
This flag is set when a capture event occurs on the ICP1 pin. When the Input Capture Register
(ICR1) is set by the WGM1[3:0] to be used as the TOP value, the ICF1 flag is set when the coun-
ter reaches the TOP value.
ICF1 is automatically cleared when the Input Capture Interrupt Vector is executed. Alternatively,
ICF1 can be cleared by writing a logic one to its bit location.
• Bits 4:3 – Res: Reserved Bits
These bits are reserved bits in the ATtiny24A/44A/84A and will always read as zero.
• Bit 2 – OCF1B: Timer/Counter1, Output Compare B Match Flag
This flag is set in the timer clock cycle after the counter (TCNT1) value matches the Output
Compare Register B (OCR1B).
Note that a Forced Output Compare (1B) strobe will not set the OCF1B flag.
OCF1B is automatically cleared when the Output Compare Match B Interrupt Vector is exe-
cuted. Alternatively, OCF1B can be cleared by writing a logic one to its bit location.
• Bit 1 – OCF1A: Timer/Counter1, Output Compare A Match Flag
This flag is set in the timer clock cycle after the counter (TCNT1) value matches the Output
Compare Register A (OCR1A).
Note that a Forced Output Compare (1A) strobe will not set the OCF1A flag.
OCF1A is automatically cleared when the Output Compare Match A Interrupt Vector is exe-
cuted. Alternatively, OCF1A can be cleared by writing a logic one to its bit location.
• Bit 0 – TOV1: Timer/Counter1, Overflow Flag
The setting of this flag is dependent of the WGM1[3:0] bits setting. In Normal and CTC modes,
the TOV1 flag is set when the timer overflows. See
behavior when using another WGM1[3:0] bit setting.
TOV1 is automatically cleared when the Timer/Counter1 Overflow Interrupt Vector is executed.
Alternatively, TOV1 can be cleared by writing a logic one to its bit location.
Bit
0x0B (0x2B)
Read/Write
Initial Value
R
7
–
0
R
6
–
0
ICF1
R/W
5
0
R
4
–
0
Table 12-5 on page 108
R
3
–
0
OCF1B
R/W
2
0
OCF1A
R/W
1
0
for the TOV1 flag
TOV1
R/W
0
0
8183C–AVR–03/11
TIFR1