PIC14000-04/SS Microchip Technology, PIC14000-04/SS Datasheet - Page 83

• Manufacturer Part Number: PIC14000-04/SS
• Description: IC MCU OTP 4KX14 A/D 28SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 14r

Specifications of PIC14000-04/SS

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 4MHz
• Connectivity: I²C
• Peripherals: POR, Temp Sensor, WDT
• Number Of I /o: 20
• Program Memory Size: 7KB (4K x 14)
• Program Memory Type: OTP
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 6 V
• Data Converters: Slope A/D
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-SSOP
• Processor Series: PIC14000
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 192 B
• Interface Type: SPI, UART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 1
• Operating Supply Voltage: 2.7 V to 6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: 0 C
• On-chip Adc: 14 bit
• For Use With: 309-1025 - ADAPTER 28-SSOP TO 28-DIPXLT28SS-1 - SOCKET TRANSITION ICE 28SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

10.6.1
An external interrupt can be generated via the
OSC1/PBTN pin if IN (internal oscillator) mode is
enabled. This interrupt is falling edge triggered. When
a valid edge appears on OSC1/PBTN pin, PBIF
(PIR1<4>) is set. This interrupt can be disabled by
clearing PBIE (PIE1<4>). PBIF must be cleared in soft-
FIGURE 10-10: EXTERNAL (OSC1/PBTN) INTERRUPT TIMING
1996 Microchip Technology Inc.
INSTRUCTION FLOW
INTERNAL
OSC
CLKOUT(3)
PBTN pin
PBIF flag
(PIR<4>)
GIE bit
(INTCON<7>)
PC
Instruction
fetched
Instruction
executed
EXTERNAL INTERRUPT
Notes:
1. PBIF flag is sampled here (every Q1)
2. Interrupt latency = 3-4Tcy where Tcy = instruction cycle time.
3. Available only in IN oscillator mode on OSC2.
4. For minimum width spec of PBTN pulse, refer to AC specs.
5. PBIF is enabled to be set anytime during the Q4-Q1 cycles.
Latency is the same whether Inst (PC) is a single cycle or a 2-cycle instruction.
Q1
Inst (PC-1)
Inst (PC)
1
Q2
PC
Q3 Q4
4
5
Q1
Inst (PC+1)
Inst (PC)
Q2
1
PC+1
Q3 Q4
Preliminary
Interrupt Latency
(Note 2)
Q1
Dummy Cycle
Q2
ware in the interrupt service routine before re-enabling
the interrupt. This interrupt can wake up the processor
from SLEEP if PBIE bit is set (interrupt enabled) prior
to going into SLEEP mode. The status of the GIE bit
determines whether or not the processor branches to
the interrupt vector following wake-up. The timing of the
external interrupt is shown in Figure 10-10.
PC+1
—
Q3 Q4
Q1
Dummy Cycle
Inst (0004h)
Q2
0004h
Q3 Q4
PIC14000
Q1
DS40122B-page 83
Inst (0005h)
Q2
Inst (0004h)
0005h
Q3 Q4