C8051F301-GS Silicon Laboratories Inc, C8051F301-GS Datasheet - Page 121

• Manufacturer Part Number: C8051F301-GS
• Description: IC 8051 MCU 8K FLASH 14-SOIC
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F30xr

Specifications of C8051F301-GS

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C/SMBus/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 8
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F300DK
• Minimum Operating Temperature: - 40 C
• Package: 14SOIC
• Device Core: 8051
• Family Name: C8051F30x
• Maximum Speed: 25 MHz
• Operating Supply Voltage: 3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1444 - ADAPTER PROGRAM TOOLSTICK F300336-1319 - REFERENCE DESIGN STEPPER MOTOR
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1536-5

ARBLOST
TXMODE
MASTER
ACKRQ
STO
ACK
STA
Bit
SI
• A START is generated.
• START is generated.
• The SMBus interface enters transmitter mode
• A START followed by an address byte is
• A STOP is detected while addressed as a
• Arbitration is lost due to a detected STOP.
• A byte has been received and an ACK
• A repeated START is detected as a MASTER
• SCL is sensed low while attempting to gener-
• SDA is sensed low while transmitting a ‘1’
• The incoming ACK value is low (ACKNOWL-
• A START has been generated.
• Lost arbitration.
• A byte has been transmitted and an
• A byte has been received.
• A START or repeated START followed by a
• A STOP has been received.
Table 13.3. Sources for Hardware Changes to SMB0CN
(after SMB0DAT is written before the start of
an SMBus frame).
received.
slave.
response value is needed.
when STA is low (unwanted repeated START).
ate a STOP or repeated START condition.
(excluding ACK bits).
EDGE).
ACK/NACK received.
slave address + R/W has been received.
Set by Hardware When:
Rev. 2.9
C8051F300/1/2/3/4/5
• A STOP is generated.
• Arbitration is lost.
• A START is detected.
• Arbitration is lost.
• SMB0DAT is not written before the
• Must be cleared by software.
• A pending STOP is generated.
• After each ACK cycle.
• Each time SI is cleared.
• The incoming ACK value is high (NOT
• Must be cleared by software.
start of an SMBus frame.
ACKNOWLEDGE).
Cleared by Hardware When:
121