PIC18F4321-I/PT Microchip Technology, PIC18F4321-I/PT Datasheet - Page 228

• Manufacturer Part Number: PIC18F4321-I/PT
• Description: IC PIC MCU FLASH 4KX16 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4321-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 8KB (4K x 16)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: EUSART/I2C/MSSP/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT44PT3 - SOCKET TRAN ICE 44MQFP/TQFPAC164305 - MODULE SKT FOR PM3 44TQFP444-1001 - DEMO BOARD FOR PICMICRO MCUAC164020 - MODULE SKT PROMATEII 44TQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F4321 FAMILY
18.4.2
The operation of the Synchronous Master and Slave
modes is identical, except in the case of Sleep, or any
Idle mode and bit SREN, which is a “don’t care” in
Slave mode.
If receive is enabled by setting the CREN bit prior to
entering Sleep or any Idle mode, then a word may be
received while in this low-power mode. Once the word
is received, the RSR register will transfer the data to the
RCREG register; if the RCIE enable bit is set, the
interrupt generated will wake the chip from the low-
power mode. If the global interrupt is enabled, the
program will branch to the interrupt vector.
TABLE 18-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
DS39689E-page 226
INTCON
PIR1
PIE1
IPR1
RCSTA
RCREG
TXSTA
BAUDCON
SPBRGH
SPBRG
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave reception.
Note 1:
Name
These bits are unimplemented on 28-pin devices and read as ‘0’.
EUSART SYNCHRONOUS SLAVE
RECEPTION
EUSART Receive Register
EUSART Baud Rate Generator Register High Byte
EUSART Baud Rate Generator Register Low Byte
GIE/GIEH PEIE/GIEL TMR0IE
ABDOVF
PSPIF
PSPIE
PSPIP
CSRC
SPEN
Bit 7
(1)
(1)
(1)
RCIDL
ADIE
ADIP
ADIF
Bit 6
RX9
TX9
RXDTP
SREN
TXEN
RCIF
RCIE
RCIP
Bit 5
Preliminary
TXCKP
INT0IE
CREN
SYNC
Bit 4
TXIF
TXIE
TXIP
ADDEN
SENDB
BRG16
SSPIE
SSPIP
To set up a Synchronous Slave Reception:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. If using interrupts, ensure that the GIE and PEIE
SSPIF
RBIE
Bit 3
Enable the synchronous master serial port by
setting bits SYNC and SPEN and clearing bit
CSRC.
If interrupts are desired, set enable bit RCIE.
If the signal from the CK pin is to be inverted, set
the TXCKP bit. If the signal from the DT pin is to
be inverted, set the RXDTP bit.
If 9-bit reception is desired, set bit RX9.
To enable reception, set enable bit CREN.
Flag bit, RCIF, will be set when reception is
complete. An interrupt will be generated if
enable bit, RCIE, was set.
Read the RCSTA register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG register.
If any error occurred, clear the error by clearing
bit CREN.
bits in the INTCON register (INTCON<7:6>) are
set.
TMR0IF
CCP1IE
CCP1IP
CCP1IF
BRGH
FERR
Bit 2
—
TMR2IF
TMR2IE
TMR2IP
INT0IF
OERR
TRMT
WUE
© 2007 Microchip Technology Inc.
Bit 1
TMR1IF
TMR1IE
TMR1IP
ABDEN
RX9D
TX9D
RBIF
Bit 0
on page
Values
Reset
49
52
52
52
51
51
51
51
51
51