tja1053 NXP Semiconductors, tja1053 Datasheet
tja1053
Available stocks
Related parts for tja1053
tja1053 Summary of contents
Page 1
... DATA SHEET TJA1053 Fault-tolerant CAN transceiver Product specification Supersedes data of 1997 Oct 15 File under Integrated Circuits, IC18 INTEGRATED CIRCUITS 2000 Dec 18 ...
Page 2
... Low current sleep/standby mode with wake-up via the bus lines Power-on reset flag on the output. GENERAL DESCRIPTION The TJA1053 is the interface between the CAN protocol controller and the physical bus primarily intended for low-speed applications 125 kbaud, in passenger cars. The device provides differential transmit capability but will switch in error conditions to a single-wire transmitter and/or receiver ...
Page 3
... DESCRIPTION plastic small outline package; 14 leads; body width 3.9 mm BAT 14 TEMPERATURE WAKE-UP PROTECTION STANDBY CONTROL DRIVER TJA1053 FAILURE DETECTOR PLUS WAKE UP PLUS TIME-OUT RECEIVER Fig.1 Block diagram. 3 Product specification TJA1053 VERSION SOT108 12 RTL 11 CANH 12 CANL 8 RTH FILTER FILTER MGL181 ...
Page 4
... LOW in dominant state GND 13 ground BAT 14 battery voltage 2000 Dec 18 handbook, halfpage INH 1 TXD 2 RXD 3 TJA1053T 4 NERR STB WAKE MGL182 Fig.2 Pin configuration. 4 Product specification TJA1053 14 BAT 13 GND 12 CANL 11 CANH RTL 8 RTH ...
Page 5
... Philips Semiconductors Fault-tolerant CAN transceiver FUNCTIONAL DESCRIPTION The TJA1053 is the interface between the CAN protocol controller and the physical bus primarily intended for low speed applications 125 kbaud, in passenger cars. The device provides differential transmit capability to the bus and differential receive capability to the CAN controller ...
Page 6
... LOW wake-up interrupt signal if V floating floating HIGH active LOW V BAT power-on flag HIGH active LOW error fl Product specification TJA1053 RXD is present switched switched to V switched to V active LOW wake-up switched to V interrupt HIGH = receive; switched to V LOW = dominant ...
Page 7
... Fig.6 150 15 0.3 0.3 load dump; 500 ms 500 note note 2 2000 note 3 200 = The rating for T limits the allowable combinations vj vj resistor. CONDITIONS VALUE 120 7 Product specification TJA1053 MAX. UNIT +6 0 +27 V +40 V +100 0.3 V BAT 0.3 V BAT + ...
Page 8
... 200 < < < 0. 100 320 2. 1.7 3.0 Product specification TJA1053 MAX. UNIT 500 200 A 800 A 4 ...
Page 9
... V; TXD = 0 V CANH sleep mode CANH TXD = 0 V CANL sleep mode CANL BAT normal mode 6.5 standby/sleep mode V 2.4 1.2 0.2 failures 4, 6 and 7 1.5 failure 3 2.8 9 Product specification TJA1053 MIN. TYP. MAX. UNIT 0.8 V 1.0 V 5.0 +5.0 3.25 2.65 V 0 100 mA ...
Page 10
... 3.3 nF 100 ; no failures and bus failures 1, 2 and 100 pF 100 ; bus failures and 3.3 nF 100 ; bus failures and 7 10 Product specification TJA1053 MIN. TYP. MAX 12 ...
Page 11
... BAT low power modes BAT normal mode and failure 0.75 modes 5 normal mode 11 Product specification TJA1053 MIN. TYP. MAX. UNIT 0.95 1.5 s 2.2 3.0 s 0.85 1.3 s 1.4 2 400 s 60 ...
Page 12
... TJA1053 RXD GND NERR Fig.3 Test circuit for dynamic characteristics. t PD(L) Fig.4 Timing diagram for dynamic characteristics. 12 Product specification (1) ( RTH 8 CANL 12 (2) C2 CANH 11 RTL 9 (1) ( MGL183 3 2 0. PD(H) MGL184 TJA1053 ...
Page 13
... Dec 18 P8xC592/P8xCE598 CAN CONTROLLER CTX0 CRXO TXD RXD STB NERR TJA1053 CAN TRANSCEIVER RTH CANH CANL CAN BUS LINE Fig.5 Application of the TJA1053 INH BAT WAKE 7 TXD 2 12 STB 5 TJA1053 RXD GND NERR Fig ...
Page 14
... REFERENCES JEDEC EIAJ MS-012 detail 1.0 0.7 1.05 0.25 0.25 0.4 0.6 0.039 0.028 0.041 0.01 0.01 0.016 0.024 EUROPEAN PROJECTION Product specification TJA1053 SOT108 ( 0.7 0 0.028 0.004 0.012 ISSUE DATE 97-05-22 99-12-27 ...
Page 15
... Use a low voltage ( less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 15 Product specification TJA1053 ...
Page 16
... Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. 2000 Dec 18 SOLDERING METHOD WAVE not suitable (2) not suitable suitable (3)(4) not recommended (5) not recommended 16 Product specification TJA1053 (1) REFLOW suitable suitable suitable suitable suitable ...
Page 17
... Product specification TJA1053 (1) These products are not Philips Semiconductors ...
Page 18
... Philips Semiconductors Fault-tolerant CAN transceiver 2000 Dec 18 NOTES 18 Product specification TJA1053 ...
Page 19
... Philips Semiconductors Fault-tolerant CAN transceiver 2000 Dec 18 NOTES 19 Product specification TJA1053 ...
Page 20
Philips Semiconductors – a worldwide company Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. + 101 ...