MAT02 Analog Devices, Inc., MAT02 Datasheet
MAT02
Available stocks
Related parts for MAT02
MAT02 Summary of contents
Page 1
... No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. 0.3 The MAT02 should be used in any application where low noise is a priority. The MAT02 can be used as an input . BE stage to make an amplifier with noise voltage of less than 1.0 nV/√ ...
Page 2
... swept from the indicated collector currents. CB MAX 100 (∆ min –2– MAT02E MAT02F Typ Max Min Typ Max 605 400 605 590 400 590 550 300 550 485 200 485 0 ...
Page 3
... Case Temperature ≤ 40° 1.8 W Ambient Temperature ≤ 70° 500 mW Operating Temperature Range MAT02E –25°C to +85°C Model MAT02EH MAT02FH CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. ...
Page 4
... Performance Characteristics MAT02 TPC 1. Current Gain vs. Collector Current TPC 4. Base-Emitter-On Voltage vs. Collector Current TPC 7. Saturation Voltage vs. Collector Current TPC 2. Current Gain vs. Temperature TPC 5. Small Signal Input Resistance vs. Collector Current TPC 8. Noise Voltage Density vs. Frequency –4– TPC 3. Gain Bandwidth vs. Collector Current TPC 6 ...
Page 5
... Leakage vs. Temperature TPC 16. Collector-to-Collector Capacitance vs. Reverse Bias Voltage REV. E TPC 11. Total Noise vs. Collective Current TPC 14. Collector-to-Collector Capacitance vs. Collector-to Substrate Voltage TPC 17. Emitter-Base Capacitance vs. Reverse Bias Voltage –5– MAT02 TPC 12. Collector-to-Base Leakage vs. Temperature TPC 15. Collector-Base Capacitance vs. Reverse Bias Voltage ...
Page 6
... MAT02 LOG CONFORMANCE TESTING The log conformance of the MAT02 is tested using the circuit shown above. The circuit employs a dual transdiode logarithmic converter operating at a fixed ratio of collector currents that are swept over a 10:1 range. The output of each transdiode converter is the V of the transistor plus an error term which is the prod- ...
Page 7
... For the MAT02 ø, ε Ø ø and therefore (5) CB The In (I ± 0.6% from each pair when using the MAT02, and this gain error is easily trimmed out by varying R , all of CB –7– . The r I term causes departure from the desired ...
Page 8
... The error from cancelled Since the MAT02 bulk resistance is approximately 0.39 Ω 3.9 Ω and will give good error cancellation more complex circuits, such as the circuit in Figure 3, it may be inconvenient to apply a compensation voltage to each indi- vidual base. A better approach is to sum all compensation to the bases of Q1. The “ ...
Page 9
... tionship. Linearity of better than 0.1% is readily achievable with this circuit if the MAT02 pairs are carefully kept at the same temperature. REV. E Figure 6. Multifunction Converter MULTIFUNCTION CONVERTER The multifunction converter circuit provides an accurate means of squaring, square rooting, and raising ratios to arbitrary pow- and I ers ...
Page 10
... The MAT02 noise voltage is exceptionally low, only 1 nV/√ when operated over a collector current range mA. A single-ended ×1000 amplifier that takes advantage of this low MAT02 noise level is shown in Figure 8. In addition to low noise, the amplifier has very low drift and high CMRR. An and A ...
Page 11
... This can be accomplished by slightly unbalancing the collector load resistors. This adjustment will reduce the drift to less than 0.1 µV/°C. REV. E Input bias current is relatively low due to the high current gain of the MAT02. The minimum β of 400 for the MAT02F implies an input bias current of approximately 2.5 µ This circuit should be used with signals having relatively low of 3 kΩ ...
Page 12
... MAT02 0.040 (1.02) MAX Revision History Location 4/02—Data Sheet changed from REV REV. E. Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1/02—Data Sheet changed from REV REV. D. Edits to FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Edits to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Edits to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Deleted ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Deleted WAFER TEST LIMITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Deleted TYPICAL ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Deleted DICE CHARACTERISTICS ...