ISL89160 INTERSIL [Intersil Corporation], ISL89160 Datasheet
ISL89160
Available stocks
Related parts for ISL89160
ISL89160 Summary of contents
Page 1
... High Speed, Dual Channel, 6A, 4.5 to 16V Power MOSFET Driver ISL89160, ISL89161, ISL89162 The ISL89160, ISL89162, and ISL89162 are high-speed, 6A, dual channel MOSFET drivers. These parts are identical to the ISL89163, ISL89164, ISL89165 drivers but without the enable inputs for each channel. Precision thresholds on all logic inputs allow the use of external RC circuits to generate accurate and stable time delays on both inputs, INA and INB ...
Page 2
... ISL89162FR, ISL89162FB (8 LD TDFN, EPSOIC) TOP VIEW NC 1 /INA 2 GND 3 INB 4 2 ISL89160, ISL89161, ISL89162 For options A and B, the UV comparator holds off the outputs until V ~> 3. For option C, the UV release is ~> 6.5V ISL89160 ISL89161, ISL89162 Pin Descriptions PIN (8 LD TDFN, EPSOIC) ...
Page 3
... SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see device information page for information on MSL, please see Technical Brief TB363. 3 ISL89160, ISL89161, ISL89162 TEMP RANGE (°C) INPUT CONFIGURATION -40 to +125 ...
Page 4
... INA, INB Input Capacitance INA, INB (Note 8) Input Bias Current I IN for INA, INB 4 ISL89160, ISL89161, ISL89162 Thermal Information Thermal Resistance (Typical TDFN Package (Notes EPSOIC Package (Notes Max Power Dissipation at +25°C in Free Air . . . . . . . . . 2.27W Max Power Dissipation at +25° ...
Page 5
... Rising Propagation Matching (see Figure 1) Falling Propagation Matching (see Figure 1) Miller Plateau Sink Current (See Test Circuit Figure 3) 5 ISL89160, ISL89161, ISL89162 V = 12V, GND = 0V, No load on OUTA or OUTB, unless otherwise specified. DD Boldface limits apply over the operating junction temperature range, -40°C to +125°C. (Continued) ...
Page 6
... FIGURE 1. PROP DELAYS AND MATCHING ISL8916x 10V 0.1µF 200ns 10nF FIGURE 3. MILLER PLATEAU SINK CURRENT TEST CIRCUIT 6 ISL89160, ISL89161, ISL89162 V = 12V, GND = 0V, No Load on OUTA or OUTB, Unless Otherwise Specified. DD Boldface limits apply over the operating junction temperature range, -40°C to +125°C. (Continued) TEST CONDITIONS SYMBOL ...
Page 7
... Typical Performance Curves 3.5 +125°C 3.0 +25°C -40°C 2.5 2 FIGURE LOAD 0.2 0.4 0.6 0.8 1.0 1.2 FREQUENCY (MHz) FIGURE FREQUENCY (+25° ISL89160, ISL89161, ISL89162 V FIGURE 6. MILLER PLATEAU SOURCE CURRENT (STATIC) 1.1 16V 1.0 0.9 10V 0.8 12V 5V 0.7 0.6 0.5 1.4 1.6 1.8 2.0 -45 Current through ...
Page 8
... To prevent unexpected glitches on the output of the ISL89160, ISL89161, ISL89162 during power-on or power-off when V is very low, the Undervoltage (UV) DD lock-out prevents the outputs of the ISL89160, ISL89161, ISL89162 driver from turning on. The UV lock-out forces the driver outputs to be low when VDD < ~3.2 VDC regardless of the input logic level. 8 ...
Page 9
... A practical maximum value, limited by contamination on the PCB, is 1MΩ. Power Dissipation of the Driver The power dissipation of the ISL89160, ISL89161, ISL89162 is dominated by the losses associated with the gate charge of the driven bridge FETs and the switching frequency. The internal bias current also contributes to the total dissipation but is usually not significant as compared to the gate charge losses ...
Page 10
... FETs, the two low side bridge FETs are turned on with a rising edge delay. The delay is setup by the RCD network on the inputs to the ISL89160. The duration of the delay is chosen to turn on the low-side FETs when the voltage on their respective drains is at the resonant valley ...
Page 11
... EPAD to the gnd plane on the bottom layer. The number of vias and the size of the gnd planes required for adequate heatsinking is determined by the power dissipated by the ISL89160, ISL89161, ISL89162, the air flow and the maximum temperature of the air around the IC. ...
Page 12
... Applications, Related Documentation and Related Parts, please see the respective device information page on intersil.com: To report errors or suggestions for this datasheet, please go to FITs are available from our website at 12 ISL89160, ISL89161, ISL89162 for a complete list of Intersil product families. ISL89160, ISL89161, ISL89162 www.intersil.com/askourstaff http://rel.intersil.com/reports/sear CHANGE FN7719.0 November 2, 2010 ...
Page 13
... Package Outline Drawing L8.3x3I 8 LEAD THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE Rev 1 6/09 3.00 (4X) 0.15 6 PIN 1 INDEX AREA TOP VIEW ( 2. 1.95) (1.64) ( 2.80 ) PIN 1 (6x 0.65) TYPICAL RECOMMENDED LAND PATTERN 13 ISL89160, ISL89161, ISL89162 2X 1.950 0.400 ± 0.10 Max 0. 0.60 0.30) NOTES 0. 1.64 +0.10/ - 0.15 PIN #1 INDEX AREA ...
Page 14
... No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see 14 ISL89160, ISL89161, ISL89162 M8.15D 8 LEAD NARROW BODY SMALL OUTLINE EXPOSED PAD M ...