T528Z337M004ATE009 Kemet, T528Z337M004ATE009 Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/3/365/kemet_sml.jpg)
T528Z337M004ATE009
Manufacturer Part Number
T528Z337M004ATE009
Description
CAP TANT 330UF 4V 20% SMD
Manufacturer
Kemet
Series
T528r
Type
Moldedr
Datasheet
1.T528Z157M006ATE012.pdf
(16 pages)
Specifications of T528Z337M004ATE009
Capacitance
330µF
Voltage - Rated
4V
Tolerance
±20%
Esr (equivalent Series Resistance)
9.0 mOhm
Operating Temperature
-55°C ~ 105°C
Mounting Type
Surface Mount
Package / Case
2917 (7343 Metric)
Size / Dimension
0.287" L x 0.169" W (7.30mm x 4.30mm)
Height
0.067" (1.70mm)
Manufacturer Size Code
Z
Features
Polymer
Voltage Rating
4 Volts
Esr
0.009 Ohms
Operating Temperature Range
- 55 C to + 85 C
Dimensions
4.3 mm W x 7.3 mm L x 1.7 mm H
Dissipation Factor Df
10
Leakage Current
132 uAmps
Product
Tantalum Organic Polymer Standard Grade
Ripple Current
6000 mAmps
Termination Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Spacing
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
399-5258-2
KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
Table 5 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and
2. The tape with or without components shall pass around R without damage (see Figure 5).
3. If S
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity defi ned by A
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Tape Size
Tape Size
B
hole location shall be applied independent of each other.
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12mm tapes and 10° maximum for 16mm tapes (see Figure 3).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8mm and 12mm wide tape and to 1.0mm maximum for 16mm tape (see Figure 4).
(e) for KPS Series product A
(f) see Addendum in EIA Document 481 for standards relating to more precise taping requirements.
12mm
16mm
12mm
16mm
1
8mm
8mm
S
1
<1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Document 481 paragraph 4.3 (b)).
1
B
including draft concentric about B
1
is for tape feeder reference only,
T
T
Ko
T
(0.059 +0.004/-0.0)
Cover Tape
2
1
Single (4mm) &
Double (8mm)
1.5 +0.10/-0.0
Triple (12mm)
Single (4mm)
Pitch
D
0
0
, B
Center Lines of Cavity
0
and K
0
and B
o
.
0
shall surround the component with suffi cient clearance that:
0
are measured on a plane 0.3mm above the bottom of the pocket.
B
D
(0.039)
(0.059)
(0.323)
(0.476)
Note 1
Note 4
(0.171)
ØDo
1
4.35
1
12.1
8.2
1.0
1.5
User Direction of Unreeling
Max.
Min.
P
Constant Dimensions — Millimeters (Inches)
Variable Dimensions — Millimeters (Inches)
2
(0.069 ± 0.004)
1.75 ± 0.10
Po
P
1
E
(0.246)
(0.404)
(0.561)
10.25
14.25
6.25
2
E
Min.
1
tolerance on tape ±0.2 mm]
[10 pitches cumulative
Ao
ØD
1
(0.157 ± 0.004)
(0.138 ± 0.002)
(0.217 ± 0.002)
(0.217 ± 0.002)
Bo
3.5 ± 0.05
5.5 ± 0.05
5.5 ± 0.05
4.0 ± 0.10
see Note 1 Table 5
Embossment
For cavity size,
P
F
0
F
E
2
E
1
W
(0.079 ± 0.002)
(0.157 ± 0.004)
(0.315 ± 0.004)
(0.315 ± 0.004)
2.0 ± 0.05
4.0 ± 0.10
8.0 ± 0.10
8.0 ± 0.10
P
P
2
1
(0.984)
T
(0.098)
Note 2
(1.181)
(0.181)
(0.181)
R Ref.
25.0
2
2.5
4.6
4.6
30
Max
S
W Max
(0.327)
(0.484)
(0.642)
(0.024)
Note 3
0.600
12.3
16.3
1
8.3
T2018-1 • 1/17/2011
Min.
T Max.
(0.024)
0.600
A
0
Note 5
,B
0
& K
T
(0.004)
0.100
1
Max.
0
11 11