EEF-CX0E331XR Panasonic - ECG, EEF-CX0E331XR Datasheet - Page 16

• Manufacturer Part Number: EEF-CX0E331XR
• Description: CAP 330UF 2.5V SPEC POLYMER SMD
• Manufacturer: Panasonic - ECG
• Series: SP-Cap CXr

Specifications of EEF-CX0E331XR

• Capacitance: 330µF
• Voltage Rating: 2.5V
• Tolerance: ±20%
• Lifetime @ Temp.: 1000 Hrs @ 105°C
• Operating Temperature: -40°C ~ 105°C
• Features: Polymer
• Ripple Current: 3A
• Esr (equivalent Series Resistance): 12.0 mOhm
• Mounting Type: Surface Mount
• Package / Case: 2917 (7343 Metric)
• Size / Dimension: 0.287" L x 0.169" W (7.30mm x 4.30mm)
• Height: 0.075" (1.90mm)
• Surface Mount Land Size: 0.287" L x 0.169" W (7.30mm x 4.30mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Spacing: -
• Other names: EEFCX0E331XR; PCE4937TR

Design, Specifications are subject to change without notice.
about safety comes up with this product, please contact us immediately for engineering assistance without fail. Specifications are typical and may not apply to all applications.
9.3 Others
9.2.4 Transportation
9.2.5 Circuit Board Cleaning
9.3.1 Precautions for using capacitors
9.3.2 Emergency Procedures
9.3.3 Capacitor Disposal
(2) Heat stress of re-flow, etc.
(3) Repair and modification by soldering iron.
(4) Mechanical stress
Take sufficient care during handling because excessive vibration, or shock can cause the reliability of the
capacitor to decrease.
Products should be cleaned after soldering in accordance with the following conditions.
Temperature: Less than 60°C
Time: Within 5min(Ultrasound OK)
Be sure to sufficiently wash and dry (20min at 100°C) the board afterward.
[Recommended cleaning solvents]
Note1: Consult our factory when performing processes with cleaning solvents other than those listed above.
Before using the products, carefully check the effects on their quality and performance, and determined
whether or not they can be used. These products are designed and manufactured for general-purpose and
standard use in general electronic equipment. These products are not intended for use in the following special
conditions.
(1) In liquid, such as Water, Oil, Chemicals, or Organic solvent
(2) In direct sunlight, outdoors, or in dust
(3) In vapor, such as dew condensation water of resistive element, or water leakage, salty air, or air with a
(4) In an environment where strong static electricity or electromagnetic waves exist
(5) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near these
(6) Sealing or coating of these products or a printed circuit board on which these products are mounted, with
(7) Using resolvent, water or water-soluble cleaner for flux cleaning agent after soldering.
(8) Acid or alkaline environments.
(9) Environment subject to excessive vibration and shock.
If the capacitor is overheated, the resin case may emit smoke. If this occurs, immediately switch off the unit's
main power supply to stop operation. Keep your face and hands away from the capacitor, since the
temperature may be high enough to cause the capacitor to ignite and burn.
Since capacitors are composed of various metals and resins, treat them as industrial waste when arranging
for their disposal.
Specified re-flow conditions must be strictly observed.
Soldering under other conditions can cause short circuits and increases in ESR.
When using a soldering iron, set the tip temperature to no more than 350°C, and work in as short a time
as possible under 10s. While soldering, do not apply strong force to the capacitor.
Do not apply excessive force to the capacitor, since this can damage the electrodes and badly affect
the capacitor’s mountability. It can also cause the increase of leakage current, separation of the lead wire
and element, and damage to the capacitor body, all of which can badly affect the electrical performance
of the capacitor.
Pine Alpha ST-100S, Clean-thru 750H, Clean-thru 750L, Clean-thru710M, Aqua Cleaner 210SEP
Sunelec B-12, DK beclear CW-5790, Techno Cleaner 219, Cold Cleaner P3-375, Telpen Cleaner EC-7R
Techno Care FRW-17, Techno Care FRW-1, Techno care FRV-1, AXREL32
high concentration corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2
products
resin and other material
(In particular, when using water or a water-soluble cleaning agent, be careful not to leave water residues)
2: The use of ozone depleting cleaning agents are not recommended in the interest of protecting the
environment.
Specialty Polymer Aluminum Electrolytic Capacitors
Panasonic Electronic Devices Co.,Ltd
Product Specification
Contact your nearest Panasonic sales office for the latest specifications prior to purchase and/or use.
(CX/SX)
E-XS-ML-5001-1
Whenever any doubt
14