ZX-TDA41 2M Omron, ZX-TDA41 2M Datasheet - Page 7

• Manufacturer Part Number: ZX-TDA41 2M
• Description: AMP UNIT 12-24VDC PWR SPLY PNP
• Manufacturer: Omron

Specifications of ZX-TDA41 2M

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: ZX-TDA412M; ZXTDA412M

Ratings and Specifications
Sensor Heads (Long-range Type)
Amplifier Units
Item
Measurement period
Possible average count settings
Linear output
Judgement outputs
(3 outputs: HIGH/PASS/LOW)
Zero reset input, timing input, reset input,
judgement output hold input
Function
Indicators
Power supply voltage
Current consumption
Ambient temperature
Temperature characteristic
Connection method
Weight
Materials
Model
Vacuum retract (VR) and air push (AP) compatible
Measurement range
Maximum actuator travel distance
Resolution
Linearity
Operating force
Air pressure
Degree of protection
Mechanical durability
Ambient temperature
Ambient humidity
Temperature characteristic
(See note 4.)
Vibration resistance
Shock resistance
Connection method
Weight
Materials
Accessories
Note: 1.
Note: 1. The response time for the first linear output or judgment output is calculated as follows (with fixed sensitivity): Measurement period
(packed state)
2.
3.
4.
5.
6.
7.
2. The output can be switched between a current output and voltage output using a switch on the base of the Amplifier Unit.
3. Setting is possible via the monitor focus function.
4. A Calculating Unit (ZX-CAL2) is required.
(packed state)
(See notes 2 and 5.)
The resolution indicates the variation (±3 σ) in the linear output (voltage output) when a ZX-TDA11/41 Amplifier Unit is connected. This value is taken 30 minutes after
turning ON the power with the average number of operations set to 1,024. The minimum value that can be read is 1 μm.
The linearity is given as the error in an ideal straight line displacement output.
These figures are representative values that apply for the mid-point of the measurement range when the Actuator provided is secured facing downward.
These figures are representative values that apply for the mid-point of the measurement range.
These values were measured at an ambient temperature of 23˚C.
The ZX-TDS10@ comes with a Right-angle Adapter.
For a Standard Actuator
The response time for the second and later outputs is the measurement period specified in the table.
Sensor Head
Rubber sleeve
Preamplifier
Mounting Brackets
Actuator contact section
(See notes 1 and 5.)
-
-
ZX-TDS10T and ZX-TDS10T-V ZX-TDS10T-VL : The operating force will be reduced if the Actuator is secured facing horizontally or upward.
ZX-TDS10T-L: The actuator can be installed only facing downward.
(See note 2.)
(See note 3.)
(See note 1.)
Vacuum retracting
Air push
Sensor Head
Preamplifier
Sensor Head
Preamplifier
(See note 7.)
Model
Prewired connector (2 m from the Sensor Head to the Preamplifier, 0.2 m from the Preamplifier to the connector)
Operating: 0 to 50°C (with no icing or condensation), Storage: −10 to 60°C (with no icing or condensation)
1 ms
1, 16, 32, 64, 128, 256, 512, or 1,024
4 to 20 mA/FS, Max. load resistance: 300 Ω ±4 V (±5 V, 1 to 5 V (See note 3.)), Output impedance: 100 Ω
NPN open-collector outputs, 30 VDC, 30 mA max.
Residual voltage: 1.2 V max.
ON: Short-circuited with 0-V terminal or 1.5 V
OFF: Open (leakage current: 0.1 mA max.)
- Measurement value display - Present value/set value/output value display
- Display reverse - ECO mode - Number of display digit changes
- Sample hold - Peak hold - Bottom hold - Peak-to-peak hold
- Self-peak hold - Self-bottom hold - Zero reset
- Initial reset - Direct threshold value setting - Position teaching
- Hysteresis width setting - Timing inputs - Reset input
- Judgement output hold input - Monitor focus - (A−B) calculations (See note 4.)
- (A+B) calculations (See note 4.) - Sensor disconnection detection - Zero reset memory
- Function lock - Non-measurement setting - Clamp value setting
- Scale inversion - Zero reset indicator - Span adjustment
- Warming-up display - Pressing force alarm
Operation indicators: High (orange), pass (green), low (yellow), 7-segment main digital display (red),
7-segment sub-digital display (yellow), power ON (green), zero reset (green), enable (green)
12 to 24 VDC ±10%, Ripple (p-p): 10% max.
140 mA max. (with Sensor connected)
Operating and storage: 0 to 50°C (with no icing or condensation)
0.03% FS/°C
Prewired (standard cable length: 2 m)
Approx. 350 g
Case: PBT (polybutylene terephthalate), Cover: Polycarbonate
Instruction manual, Preamplifier Mounting Brackets (ZX-XBT1), Right-angle Adapter
0.35-mm single amplitude at 10 to 55 Hz for 50 min each in the X, Y, and Z directions
Approx. 0.7 N
ZX-TDS10T
150 m/S
No
---
Operating and storage: 35% to 85% (with no icing or condensation)
2
Stainless steel
3 times each in 6 directions (up/down, left/right, and forward/backward)
ZX-TDA11
Viton
IP65
−0.55 to −0.70 (bar)
ZX-TDS10T-V
Approx. 0.6 N
10,000,000 operations min.
VR
---
Stainless steel
Polycarbonate
±0.01% FS/˚C
±0.01% FS/˚C
Approx. 100 g
Super steel
±0.5% FS
10.5 mm
0.4 μm
10 mm
IP40
PNP open-collector outputs, 30 VDC, 30 mA max.
Residual voltage: 2 V max.
Approx. 0.065 N
ZX-TDS10T-L
No
---
Polyamide
ZX-TDA41
(Average count setting + 1).
None
IP50
−0.22 to −0.5 (bar)
ZX-TDS10T-VL
0.09 to 1.41N
0.125 to 2 (bar)
VR/AP
(See note 6.)