ZX-XF12 Omron, ZX-XF12 Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
ZX-XF12
Manufacturer Part Number
ZX-XF12
Description
ATTACHMNT SIDEVIEW ZX-LT1001/005
Manufacturer
Omron
Specifications of ZX-XF12
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
ZXXF12
Precautions
■ Design Precautions
Ratings and Performance
• Conform to the specified ratings and performance. Refer to Speci-
• Do not disconnect the connector connecting the Sensor Head and
• Allow a warm-up period of approximately 10 minutes after turning
• Objects of certain materials or shapes may not be detectable, or the
Power Supply and Wiring
• Prior to turning ON the power supply after wiring is completed,
• The total length of the Sensor cable or Amplifier cable must be 10 m
• Do not lay a power supply cable for the ZX together with high-volt-
• When using a commercially available switching regulator, ground
• If the power supply line is subject to surges, connect a surge ab-
• When using a Calculating Unit, connect the corresponding linear
Compatibility
• All Sensor Heads and Amplifier Units are compatible. Different Sen-
Mutual Interference
• Two Sensor Heads can be used together, without danger of mutual
Maintenance
• Always turn OFF the power supply before adjusting or removing the
• Cleaning
16
fications for details.
the controller while power is being supplied, otherwise the Sensor
may be damaged.
ON the power supply.
detection accuracy may not be sufficiently high. These include ma-
terials that are transparent or have extremely low reflectivity, and
objects that are smaller than the Sensor’s spot diameter or have ex-
treme curvature or inclination.
check to make sure that the power supply is correct, that there are
no mistaken connections, e.g., connections that would short-circuit
the load, and that the load current is appropriate. Incorrect wiring
may result in damage to the Sensor or Unit.
or less. Use an ZX-XC@A Extension Cable (order separately) if re-
quired to extend the cable from the Sensor. Use a shielded cable to
extend the Amplifier cable. The shielded cable must be the same as
that of the Amplifier cable.
age lines or power lines to prevent interference, damage, and mal-
function.
the FG (frame ground) terminal.
sorber that meets the conditions of the usage environment.
ground of the Amplifier Unit.
sor Heads may be purchased at a later date and used with existing
Amplifier Units.
interference, by connecting the ZX-CAL 2 Calculating Unit between
two Amplifier Units.
Sensor Head.
Do not use thinners, benzine, acetone, or kerosene for cleaning.
If dust or oil adheres to the filter on the front of the Sensor Head,
use the following procedure to clean.
1. Do not impose voltage exceeding the rated voltage, otherwise
2. When supplying power to the Sensor, make sure that the
3. Do not short-circuit the load for the open collector output, oth-
1. Use a blower brush (used to clean camera lenses) to blow
2. Use a soft cloth (for lenses) with a small amount of alcohol to
the Sensor may be damaged.
polarity of the power is correct, otherwise, the Sensor may be
damaged. Do not connect to an AC power supply.
erwise the Sensor may be damaged.
large dust particles from the surface. Do not blow the dust
away with your mouth.
remove the remaining dust. Do not use a scrubbing action
when cleaning because scratches on the filter could result in
Sensor inaccuracy.
ZX Series (ZX-L-N)
Smart Sensors (Laser Type)
■ Other Precautions
Environment
1. Do not use the Sensor in strong electromagnetic fields or in an
2. Do not operate the Sensor in the following locations:
environment where the operation of the Sensor is subject to
the reflection of intense light (such as other laser beams or
electric arc-welding machines.)
• Locations subject to strong vibration.
• Locations subject to direct sunlight or near heating equip-
• Locations subject to high humidity.
• Locations where the Sensor would accumulate dust, dirt, me-
• Locations subject to corrosive or flammable gases.
• Locations subject to exposure to organic solvents, water, oil,
• Locations subject to strong electromagnetic or electrical
• Locations subject to rapid changes in temperature.
• Locations subject to freezing.
ment.
tallic powder, etc.
etc.
fields.