58245-3 Tyco Electronics, 58245-3 Datasheet

no-image

58245-3

Manufacturer Part Number
58245-3
Description
BOARD TOOL ASSY
Manufacturer
Tyco Electronics
Datasheet
1.58024-1.pdf (6 pages)

Specifications of 58245-3

Lead Free Status / RoHS Status
Not applicable / Not applicable
h
G
available for new applications, however the fixtures can be used with existing applications.
1. INTRODUCTION
Mass Termination Assembly (MTA) .156
Connector–Holding Fixtures listed in Figure 1 are
designed to hold .156 MTA connectors and discrete
wires in position for termination. The fixture is used
with the MTA applicator assembly or tooling assembly
(also listed in Figure 1). The fixtures are designed for
feed–through (wires are not cut) or closed end (wires
are cut) applications. The connectors are available
with up to 26 contact positions on 3.96 [.156]
centerline spacing.
E
All International Rights Reserved
AMP and Tyco are trademarks. *Trademark
Other products, logos, and company names used are the property of their respective owners.
Card Edge
Posted
With Locking Ramp and Without Polarization Tabs
With Locking Ramp and With Polarization Tabs
Without Locking Ramp and With or Without
Polarization Tabs
F
For Testing (All Types)
This applicator assembly must be used with Pneudraulic Tool 59809–2. The applicator assembly and pneudraulic tool are no longer
The tooling assembly must be used with Manual Arbor Frame Assembly 58024–1 (408–6923).
2003 Tyco Electronics Corporation, Harrisburg, PA
(A
.156
.156 MTA CONNECTOR
Front Wire Comb
)
R
This controlled document is subject to change.
For latest revision, call the FAX/PRODUCT INFO number.
Mass Termination Assembly (MTA)
.156 Connector–Holding Fixture
Feed–Through
CONNECTOR–HOLDING FIXTURE
59849–1
59849–3
58010–1
58010–2
59847–1
59847–3
58245–1
58245–2
58245–3
Figure 1
24
For information on operating the applicator or tooling
assembly, refer to the instruction sheet (indicated in
parenthesis in Figure 1) packaged with the tooling.
Read these instructions and referenced material
thoroughly before using the fixture.
Reasons for reissue of this instruction sheet are
provided in Section 7, REVISION SUMMARY.
NOTE
Closed End
59848–1
59848–3
58009–1
58009–2
59846–1
58244–3
58244–1
58244–2
58244–3
244
Dimensions in this instruction sheet are in
millimeters [with inches in brackets]. Figures are
for reference only and are not drawn to scale.
TOOLING ASSISTANCE CENTER 1–800–722–1111
FAX/PRODUCT INFO 1–800–522–6752
For Regional Customer Service, visit our website at
www.tycoelectronics.com
Housing
Support
Rear Wire Comb
APPLICATOR
ASSEMBLY
(408–4260)
(408–4260)
(408–4260)
(408–4260)
PP
59843–1
59843–1
59843–1
59843–1
59843–1
58576–1
58576–1
58576–1
58576–1
9 43
MTA
Polarizing Tab
G
G
G
G
G
R
Instruction Sheet
Locating
Plate
408–7995
26 AUG 03 Rev B
MTA TOOLING
ASSEMBLY
(40
(408–6701)
58040–1
SS
040
040
040
040
—
—
B Y
0 )
h
1 of 6
LOC B

58245-3 Summary of contents

Page 1

... Figure 1 Dimensions in this instruction sheet are in NOTE millimeters [with inches in brackets]. Figures are for reference only and are not drawn to scale. For information on operating the applicator or tooling assembly, refer to the instruction sheet (indicated in parenthesis in Figure 1) packaged with the tooling ...

Page 2

DESCRIPTION Each fixture consists of a one–piece locating plate, housing support, front wire comb, and rear wire comb. The polarizing tab is used to properly orient the applicator or tooling assembly with the fixture. 3. SETUP Select the connector ...

Page 3

... Note: Not to scale 58009–2, 58010–2, 58244–3, 58245–3, 59847–3, 59848–3, 59849–3 58244–1, 58244–2, 58245–1, 58245–2, 58009–1, 58010–1, 59849–1, 59846–1, 59847–1, 59848–1 Connector Centered on Fixture Receiving ...

Page 4

... A complete inventory should be stocked and controlled to prevent lost time when replacement of parts is necessary. Parts other than those listed should be replaced by Tyco Electronics to ensure quality and reliability. Order replacement parts through your representative, or call 1–800–526–5142, or send a facsimile of your purchase order to 717– ...

Page 5

Detail A — Replacement Parts 37 [1.45] 108 [4.25] 9.12 [.359] PART NUMBER FOR CONNECTOR–HOLDING FIXTURE ITEM 58009–1 58009–2 58010–1 1 311304–1 311304–1 311308–1 2 21017–1 21017–1 3 311306–1 311306–2 311306–1 4 — — 5 — — 6 311302–1 311302–1 ...

Page 6

... MTA .156 Connector–Holding Fixture 6.12 [.241] Ref 58245–1 58245–2 58245–3 BLADE, Cutoff — — — SCREW, Right–Hand Drive 310668–1 310668–1 — SUPPORT, Housing — — 318579–1 BASE POST RETAINER NUT, Acorn SPRING SCREW, Special, ...