91349-3 Tyco Electronics, 91349-3 Datasheet

no-image

91349-3

Manufacturer Part Number
91349-3
Description
SEATING TL 4 PR 12 COL HDR
Manufacturer
Tyco Electronics
Datasheet
1.91349-1.pdf (4 pages)

Specifications of 91349-3

Lead Free Status / RoHS Status
Not applicable / Not applicable
1. INTRODUCTION
This instruction sheet covers the use and
maintenance of Seating Tools 91348–[ ], 91349–[ ],
and 91375–1 which are used to seat Hard Metric Zd
(HM–Zd) Header Connectors with Eye of Needle
Type contacts into printed circuit (pc) boards. See
Figure 1. Tool 91348–1 is used to seat two–pair
HM–Zd Header Connectors; tools 91349–[ ] are used
to seat four–pair HM–Zd Header Connectors; and tool
91375–1 is used to seat three–pair HM–Zd Header
Connectors. These tools allow solderless printed
circuit (pc) board installation.
E
All International Rights Reserved.
AMP and Tyco are trademarks. *Trademark
Other products, logos, and company names used are the property of their respective owners.
2004 Tyco Electronics Corporation, Harrisburg, PA.
NOTE
All dimensions on this document are in metric
units [with U.S. customary units in brackets].
Figures and illustrations are for reference only,
and are not drawn to scale.
Eye of Needle Type
Contact Board
Retention Feature
Typical HM–Zd
Connector Assembly
(Ref)
This controlled document is subject to change.
For latest revision call the FAX number.
Seating Tools 91348–[ ],
91349–[ ], and 91375–1
for HM–Zd Header Connectors
Figure 1
Read these instructions and understand them before
using the seating tools and support anvil.
Reasons for reissue of this sheet are provided in
Section 8, REVISION SUMMARY.
2. DESCRIPTION
The seating tool consists of a seating tool blade and
an adapter to seat either two–, three–, or four–pair
HM–Zd Header Connectors.
During seating, the tool sits inside the header housing
engaging the housing floor and contact shoulders,
preventing contacts from pushing out of the housing.
3. REQUIREMENTS
3.1. PC Board Support Fixture (Customer Supplied)
A pc board support must be used to provide proper
support for the pc board and alignment of the tool to
TOOLING ASSISTANCE CENTER 1–800–722–1111
FAX/PRODUCT INFO 1–800–522–6752
For Regional Customer Service, visit our website at
www.tycoelectronics.com
End Row of
Ground Planes
Seating Tool
PC Board Support
(Customer Supplied)
(Ref)
Keys
PC Board
(Ref)
Instruction Sheet
408–8501
16 FEB 04 Rev D
1 of 4
LOC B

91349-3 Summary of contents

Page 1

... Contact Board Retention Feature 1. INTRODUCTION This instruction sheet covers the use and maintenance of Seating Tools 91348–[ ], 91349–[ ], and 91375–1 which are used to seat Hard Metric Zd (HM–Zd) Header Connectors with Eye of Needle Type contacts into printed circuit (pc) boards. See Figure 1. Tool 91348– ...

Page 2

... Shut Height (Ram Down) .000 .254 Seating Tools 91348–[ ], 91349–[ ], and 91375–1 chosen; slowly lower ram until it just meets the seating tool. Verify the alignment of the board support, pc board, header, and seating tool. Damage to the pc board, tool, or header may ...

Page 3

... Seating Tool 91375–1 Adapter Setscrew Rev D Seating Tools 91348–[ ], 91349–[ ], and 91375–1 50.8 [2.00 50.8 [2.00 50.8 [2.00] 24.97 12.7 [ ...

Page 4

... Seating Tools 91348–[ ], 91349–[ ], and 91375–1 7. REPLACEMENT AND REPAIR The parts listed in Figure 3 are customer– replaceable. A complete inventory can be stocked and controlled to prevent lost time when replacement of parts is necessary ...