5-1437514-5 Tyco Electronics, 5-1437514-5 Datasheet

TOOL HAND SPRING LOADED

5-1437514-5

Manufacturer Part Number
5-1437514-5
Description
TOOL HAND SPRING LOADED
Manufacturer
Tyco Electronics
Series
HOLTITEr
Type
Hand Tool, Spring Loadedr
Datasheets
1.5-1437514-5.pdf (7 pages)
2.5-1437514-3.pdf (7 pages)

Specifications of 5-1437514-5

Product
Crimping, Stripping & Cutting Tools & Drills
Lead Free Status / RoHS Status
Not applicable / Not applicable
1. INTRODUCTION
This specification covers the requirements for application of AUGAT HOLTITE Sockets. These manually
applied or reel–mounted machine applied solderless spring sockets are designed to be contained within the
barrel of a plated–through hole. The design allows the socket and plated–through hole to form a zero–profile
component socket which provides an interconnect for a broad range of electronic parts and components. The
sockets are available in a variety of different series and sizes based on printed circuit (pc) board hole diameter.
They are also available normally on mylar strips which can be reeled on custom socket patterns for ease of
application.
When corresponding with personnel, use the terminology provided in this specification to facilitate your
inquiries for information. Basic terms and features of this product are provided in Figure 1.
2. REFERENCE MATERIAL
2.1. Revision Summary
2.2. Customer Assistance
Reference Part Number 6–1437514–7 and Product Code E354 are representative numbers of AUGAT
HOLTITE Sockets. Use of these numbers will identify the product line and expedite your inquiries through a
service network established to help you obtain product and tooling information. Such information can be
obtained through a local Tyco Electronics Representative (Field Sales Engineer, Field Applications Engineer,
etc) or, after purchase, by calling the Tooling Assistance Center or Product Information number at the bottom of
this page.
E
NOTE
S
S
S
S
Updated document to corporate requirements
Deleted documents from Paragraph 2.5
Changed text in Paragraph 3.2 and CAUTION in Paragraph 3.3.B
Added Table “A” in Figure 2
All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and
inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2
Figures and illustrations are for identification only and are not drawn to scale.
AUGAT* HOLTITE* Sockets
Figure 1
www.tycoelectronics.com
114-13033
1
_
.

5-1437514-5 Summary of contents

Page 1

... All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and NOTE inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2 Figures and illustrations are for identification only and are not drawn to scale. ...

Page 2

... All sockets are made of beryllium–copper with gold, tin/lead, or tin plating. 1. Board material will be glass epoxy (FR–4, G–10). 2. Board thickness shall be 0.75 [.030] minimum for all socket sizes except for 12P which is used in a 1.27 [.050] minimum thick pc board. Contact the Product Information number listed at the bottom of page 1 for suitability of other board materials or thicknesses ...

Page 3

Holes should be drilled from the component insertion side of the pc board, whenever possible, to avoid creating drill-exit burrs on the press-fit portion of the through-hole. Finished hole tolerances should NOT be maintained by drilling over-sized holes and then ...

Page 4

... Two different tips may be used for socket insertion into the pc board. The blue tip is used for the 5P, 14P, and 27P series sockets. The other insertion tip is white and is used for the 6P, 8P, and 12P series sockets. Refer to Section 5, TOOLING for specific related tooling part numbers. ...

Page 5

... Installation of a single replacement socket can then be accomplished. These sockets are qualified to MIL–S–83505/6D. However, they are not required to be Recognized by Underwriters Laboratories Inc. (UL); or Certified to CSA International. Tyco Electronics has existing tooling and tooling concepts for applying these sockets. Part numbers of available tooling and the applicable instructional material for each is provided in Figure 7 ...

Page 6

... SM-3 Machine 814700-[ ] (409-5626) Typical Pneumatic Arbor Frame Assembly 91112-3 Typical Manual Arbor Frame Assemblies 58024-1, 91085 AUGAT HOLTITE Sockets PC Board Support Fixture Spring Loaded Hand Tool 5-1437514-3, 5-1437514-5, Pneumatic Hand Tool System 5-1437514-8 Figure 7 114-13033 (Customer Supplied) 5-1437514-7 Rev A ...

Page 7

VISUAL AID Figure 8 shows a typical application of an AUGAT HOLTITE Socket. This illustration should be used by production personnel to ensure a correctly applied product. Applications which DO NOT appear correct should be inspected using the information ...