69734 Tyco Electronics, 69734 Datasheet

no-image

69734

Manufacturer Part Number
69734
Description
DIE PIDG STRATO 69710 #14
Manufacturer
Tyco Electronics
Datasheets
1.69734.pdf (11 pages)
2.69734.pdf (11 pages)

Specifications of 69734

Product
Punches & Dies
Lead Free Status / RoHS Status
Not applicable / Not applicable
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended- - use, production operations is available.
1. INTRODUCTION
The die assemblies listed in Figure 1 will crimp
terminals and splices for the following product families
with wire sizes 26 through 10 AWG:
with wire sizes 22 through 10 AWG:
These die assemblies are designed to be used with
Hand Tool 69710--1. Refer to Instruction Sheet
408--2095 for information concerning the tool.
Contact TOOLING ASSISTANCE CENTER at the
number at the bottom of this page for other
recommended tooling.
E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
*Trademark
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
Color
Code
Stationary
Die
— PIDG* terminals and splices
— PIDG insulation restricting nylon terminals
— PIDG STRATO--THERM* terminals
— PLASTI--GRIP* terminals
— DIAMOND GRIP* terminals and splices
NOTE
i
46251--2
47806--2
47807--1
47808--5
Locator
Insulation Adjustment
Spacers in Position 3
All numerical values in this instruction sheet are
in metric units [with U.S. customary units in
brackets]. Dimensions are in millimeters [and
inches]. Figures are not drawn to scale.
CRIMPING DIE ASSEMBLIES
Note: Die Assembly Shown is Typical
Figure 1
47808--6
69342
69344
69731
Die Holding
Screw
Terminal and Splice
Crimping Die Assemblies
Color
Code
69732
69733
69734
69735
TOOLING ASSISTANCE CENTER 1--800--722--1111
PRODUCT INFORMATION 1--800--522--6752
Moving
Die
Reasons for reissue of this instruction sheet are
provided in Section 7, REVISION SUMMARY.
2. DESCRIPTION
The die assembly consists of a moving die and a
stationary die. See Figure 1.
The dies and the terminals and splices are color--
coded according to wire size for easy identification.
When the terminal and splice are properly crimped in
the correct die assembly, 1 dot or 2 dots (depending
on wire size) will appear embossed on the top and
bottom of the terminal or splice. DIAMOND GRIP
terminals and splices do not have a color code or
crimp dot code. See Figures 2, 3, and 4.
3. CRIMPING PROCEDURE
NOTE
NOTE
NOTE
1. Install the die assembly according to the
instructions included with the tool.
2. Strip the wire to the dimensions provided in
Figure 2, 3, 4, or 5; depending on the wire size and
product to be crimped.
3. Place the terminal or splice in the stationary die
as shown in Figure 6, 7, or 8.
4. Close the tool handles until the terminal or splice
is held firmly in place.
5. For a terminal, insert a stripped wire into the
insulation barrel until the wire butts against the
locator. For a splice, insert the stripped wire into an
insulation barrel until the wire butts against the wire
stop in the splice.
6. Complete the crimp by closing the tool handles
until the ratchet releases.
i
i
i
The dies are coated with oil to prevent rust and
corrosion. Wipe this oil from the dies, particularly
from the crimping area.
Refer to Paragraph 2.4 for insulation crimp
adjustment.
Dies will not accommodate terminals with tongue
width exceeding 11.91 [.469].
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
Instruction Sheet
408- - 1632
19 APR 11
1 of 11
Rev C
LOC B

69734 Summary of contents

Page 1

... See Figures 2, 3, and 4. 3. CRIMPING PROCEDURE 69732 NOTE 69733 i 69734 69735 1. Install the die assembly according to the instructions included with the tool. NOTE i 2. Strip the wire to the dimensions provided in Figure ...

Page 2

“A” Equals Strip Length “B” Equals Wire Barrel WIRE SIZE (AWG) DIE ASSEMBLY RANGE RANGE 69344 26--22 69342 24--20 47806--2 22--16 47807--1 16--14 or 20--16 HD 47808--6D 12--10 12--10 Lg Exp or 16--14 HD 47808--5D Use only ...

Page 3

... Equals Wire Barrel WIRE SIZE (AWG) WIRE SIZE (AWG) DIE ASSEMBLY DIE ASSEMBLY RANGE 69731 26--24 69732 22--20 69733 18--16 69734 14 69735D 12--10 se only in Tool 69710-- “A” Equals Strip Length “B” Equals Wire Barrel WIRE SIZE (AWG) ...

Page 4

PIDG Terminal, PIDG STRATO- THERM Terminal, PLASTI- GRIP To Locate PIDG Terminal, and STRATO- - THERM DIAMOND GRIP Terminal, Pull Locator Terminal Down Slightly Wire Barrel Against Locator Insulation Barrel Wire Barrel Section of Section of Crimping Crimping Chamber Chamber ...

Page 5

Use Position 1 for wire having a small insulation diameter. Turn both insulation adjustment spacers so that they will fit between the moving die and the die holder. No. 1 will appear on the corner of the top spacer ...

Page 6

... See Paragraph 5.3, Step 5 {Die closure dimensions apply when dies are bottomed, but not under pressure “ ...

Page 7

... Pass Completely Through Insulation Barrel Section of Crimping Chamber Figure 11 or send a facsimile of your purchase order to 717--986--7605, or write to: CUSTOMER SERVICE (038--035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105--3608 For customer repair service, call 1--800--526--5136. 7. REVISION SUMMARY Revisions to this instruction sheet include: ...

Page 8

ITEM ITEM DESCRIPTION DESCRIPTION 1 SCREW, Special 3 ANVIL, Insulation 4 ANVIL, Wire Barrel 5 SPRING 6 HOUSING, Locator 7 LOCATOR 8 RING, Retaining 9 SPACER, Lower 10 INDENTER, Wire Barrel 11 INDENTER, Insulation 12 SPACER, Insulation Adjustment 13 SPACER, ...

Page 9

ITEM DESCRIPTION 1 SCREW, Special 2 PLATE, Guide 3 ANVIL, Insulation 4 ANVIL, Wire Barrel 5 SPRING 6 HOUSING, Locator 7 LOCATOR 8 RING, Retaining 9 SPACER, Lower 10 INDENTER, Wire Barrel 11 INDENTER, Insulation 12 SPACER, Insulation Adjustment 13 ...

Page 10

ITEM ITEM DESCRIPTION DESCRIPTION 1 SCREW, Special 3 ANVIL, Insulation 4 ANVIL, Wire Barrel 5 SPRING 6 HOUSING, Locator 7 LOCATOR 8 RING, Retaining 9 SPACER, Lower 10 INDENTER, Wire Barrel 11 INDENTER, Insulation ...

Page 11

... Figure 12 (End) 408- 1632 QTY PER DIE DIE 69734 69735 ASSEMBLY 1--306131--6 3--306131--4 1 1--45932--8 1--45932--9 1 2--45904--0 2--45904--1 1 7--59683--4 7--59683--4 2 ...