58449-1 Tyco Electronics, 58449-1 Datasheet

no-image

58449-1

Manufacturer Part Number
58449-1
Description
DIE HOLDER ASSY AMPLIMITE
Manufacturer
Tyco Electronics
Type
Die Holderr
Datasheet
1.58449-1.pdf (8 pages)

Specifications of 58449-1

Lead Free Status / RoHS Status
Not applicable / Not applicable
1. INTRODUCTION
Die Holder Assemblies 58449--1, --2, and --3 are
designed to be used with 2700--lb Pneumatic Power
Unit 312522--3 to crimp the ferrules of the connectors
listed in Figure 1 onto round shielded cable.
Refer to Instruction Sheets 408--9072 (SDL
connectors) and 408--9010 (AMPLIMITE connectors)
for connector assembly and die assembly selection,
and Customer Manual 409--5843 for operating
procedure of the pneumatic power unit.
Read these instructions and any referenced
documents thoroughly before using the die holder
assembly.
E2010 Tyco Electronics Corporation, Berwyn, PA
All Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other product names, logos, or company names might be trademarks of their respective owners.
DIE HOLDER ASSEMBLY
NOTE
i
Base Plate
(Ref)
58449--1
58449--2
58449--3
Connector Support
Bracket
All numerical values in this instruction sheet are
in metric units [with U.S. customary units in
brackets]. Dimensions are in millimeters [and
inches]. Figures are not drawn to scale.
Handle
Lower Die Holder
Slide Base
(Ref)
Upper Die Holder
Shielded Data Link (SDL)
AMPLIMITE and SDL
Ram Adapter
Lower Connector
Support (Ref)
CONNECTOR
AMPLIMITE*
TOOLING ASSISTANCE CENTER 1- - 800- - 722- - 1111
PRODUCT INFORMATION 1- - 800- - 522- - 6752
Die Holder Assemblies
58449- 1, - 2, and - 3
Figure 1
Reasons for reissue of this instruction sheet are
provided in Section 8, REVISION SUMMARY.
2. DESCRIPTION
Each die holder assembly consists of two
subassemblies: an upper die holder and a lower die
holder. A clear plastic guard assembly (not shown) is
also provided to protect the operator from possible
injury during the crimping operation.
The upper die holder subassembly consists of a die
holder, a die holding plate, and a ram adapter. The
upper plate is spaced from the ram of the power unit
by the ram adapter. The ram adapter is mounted to
the ram of the power unit with four socket head cap
screws (included with the die holder assembly).
The lower die holder subassembly consists of a die
holder, a die holding plate with a guide block, a
connector support bracket, and a cable clamp spring.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
(See Figure 1)
Pneumatic
Power Unit
Upper Die Holding
Plate
Cable Clamp
Springs
Guide Block
Instruction Sheet
408- - 9721
Lower Die
Holding Plate
18 MAY 10 Rev B
1 of 8
LOC B

58449-1 Summary of contents

Page 1

... Shielded Data Link (SDL) 58449--3 AMPLIMITE and SDL 1. INTRODUCTION Die Holder Assemblies 58449--1, --2, and --3 are designed to be used with 2700--lb Pneumatic Power Unit 312522--3 to crimp the ferrules of the connectors listed in Figure 1 onto round shielded cable. Refer to Instruction Sheets 408--9072 (SDL ...

Page 2

... NOTE i Lower Die Holder Subassembly Figure 2 Tyco Electronics Corporation (See Figure 2) The socket head cap screws must be loose enough to allow the tooling to move on the ram when the upper die holder is engaged with the lower die holder. The pins of the upper die holding plate must be aligned with the locating holes of the guide block ...

Page 3

... This screw can be accessed using the .19- - in. NOTE diameter hole on the left side of the fixed guard. i Lower Die (Anvil) (Ref) Figure 3 Tyco Electronics Corporation Pin(s) Upper Die (Indenter) (Ref) Locating Hole(s) of Guide Block ...

Page 4

... Loosen the screw which secures the connector support to the bracket; then re--adjust the support. 5.4. Die Holder Assembly Conversion (For Assembly 58449- 3 Only) 1. Remove the upper and lower die holders used for the AMPLIMITE connector. 2. Install the lower die holder used for the SDL connector onto the lower tooling assembly ...

Page 5

... Alignment Gage Die Assembly (for SDL Connector, Ref) Guide Block (Ref) Rev B Upper Die Holder (for SDL Connector) Figure 4 Tyco Electronics Corporation Upper Die Holding Plate (Ref) Locator Clamping Block Tapped Hole (Ref) Lower Die Holder (for SDL Connector ...

Page 6

... A complete inventory should be stocked and controlled to prevent lost time when replacement of parts is necessary. Parts other than those listed should be replaced by Tyco Electronics to ensure quality and reliability. Order replacement parts through your representative, or call 1--800--526--5142, or send a facsimile of your purchase order to ...

Page 7

... PART NUMBER GUARD, Right GUARD, Front GUARD, Fixed SUPPORT, Lower BRACKET, Support BLOCK, Clamping BLOCK, Guide PLATE, Lower PLATE, Upper SLIDE, Base Figure 5 (Cont’d) Tyco Electronics Corporation Section 15.54 [6.12] QTY PER ASSEMBLY 58449 58449 58449 — — — — — ...

Page 8

... SCREW, Shoulder Head Cap, 8--32 ¢ .50 in. LOWER DIE HOLDER UPPER DIE HOLDER LOCATOR GUARD, Right GUARD, Front GUARD, Fixed PLATE, Lower PLATE, Upper 1 SCREW, Shoulder Head Cap, / --20 ¢ .875 in. 4 GAGE, Alignment GAGE, Alignment Figure 5 (End) Tyco Electronics Corporation 1 — — ...