1-47387-0 Tyco Electronics, 1-47387-0 Datasheet
![no-image](/images/manufacturer_photos/0/6/687/tyco_electronics_sml.jpg)
1-47387-0
Specifications of 1-47387-0
1-47387-0 Summary of contents
Page 1
... Reasons for reissue are provided in Section 8, REVISION SUMMARY. The crimping head consists of integral jaws which close in an arc–like motion. After an operator locates the terminal or splice between the crimping jaws and inserts the stripped wire, the tool is activated to crimp the terminal or splice to the wire. ...
Page 2
... HEAD HEAD NOTE: Refer to Tyco Electronics Catalog 82042 for product part numbers. 3. HEAD INSTALLATION AND REMOVAL 3.1. Head Selection The crimping heads are coded to match the terminal and splice insulation color. Observe the embossed dots on the insulation of finished crimps to ensure that ...
Page 3
... Never place anything within the crimping jaws except Tyco Electronics terminals or splices. 4.1. Terminal Crimping Procedure 1. Strip wire to dimensions shown in Figure 2. DO NOT nick wire strand or use wires with nicked or missing conductor strands. 2. Center the terminal or splice wire barrel in the appropriate crimp chamber ...
Page 4
... To crimp the other half of the butt splice, reposition it in the crimping jaws and repeat Steps 1 through 5. If the splice cannot be turned, rotate crimping head. See Figure 4B. 7. Refer to Section 5 and Figure 6 for crimp inspection. 4A PIDG Butt Splice C" B" B" Equals Wire Barrel C" ...
Page 5
... Remove dust, moisture, and other contaminants with a clean, soft brush lint–free cloth. Do NOT use objects that could damage the head. 2. Make sure that all pins, rings, and other components are in place and secure. ...
Page 6
... NOTE 6 PIDG and PLASTI-GRIP Terminal and Splice Crimping Heads Crimp Inspection ACCEPT REJECT PIDG Insulation Restricting Terminals PIDG and PLASTI-GRIP Terminals PIDG Butt Splice Figure 6 408-10029 A ...
Page 7
... JAW CRIMPING CLOSURE HEAD HEAD DIMENSIONS 0.889-1.397 1-525690-0 [.0350-.0550] 1-47386-0 0.762-1.270 1-47386-4 [.0300-.0500] 1-47387-0 1.016-1.524 1-47387-7 [.0400-.0600] 0.762-1.270 1-46121-0 [.0300-.0500] 1.143-1.651 1-525691-0 [.0450-.0650] DANGER Disconnect the battery and remove crimping head from tool before inspecting crimping chambers ...
Page 8
... CUSTOMER SERVICE (38–35) TYCO ELECTRONICS CORPORATION P.O. BOX 3608 HARRISBURG, PA 17105–3608 For further repair and replacement information, call the Tyco Electronics Tooling Assistance Center at the number at the bottom of page 1. 8. REVISION SUMMARY S Initial release of document Inspection of Insulation Crimping Section Wire Barrel Jaws ...
Page 9
... PART NUMBER FOR CRIMPING HEAD ITEM NO. 1-47387-0 1-47386-0 1 45965-6 302993 2 9-305927-1 9-305927-1 3 302994 302994 4 301201 301201 5 39207 39207 A Rev PIDG and PLASTI-GRIP Terminal and Splice Crimping Heads 2 1 CUSTOMER REPLACEMENT PARTS 1-47386-4 1-47387-7 1-46121-0 1-525690-0 1-525691-0 3-304052-6 525355-8 LOCATOR 3-306105-9 9-305927-1 SCREW, 8- ...