318451-2 Tyco Electronics, 318451-2 Datasheet

DIE SET

318451-2

Manufacturer Part Number
318451-2
Description
DIE SET
Manufacturer
Tyco Electronics
Series
Pro-Crimper™ IIIr
Type
Crimp Toolr
Datasheets
1.318451-1.pdf (5 pages)
2.318451-2.pdf (5 pages)

Specifications of 318451-2

Connector Type
Coax Connectors
Crimp Handle
Tyco/AMP 318451-1
Crimp Or Cable Size
RG/U-79, 161, 187
Features
"O" / Commercial
Crimp Application
Coaxial
Product
Crimping, Stripping & Cutting Tools & Drills
For Use With
75 Ohm BNC RF/Coaxial Connectors
Lead Free Status / RoHS Status
Not applicable / Not applicable
Lead Free Status / RoHS Status
na, Not applicable / Not applicable
Other names
318451-2
A24630
1. INTRODUCTION
PRO–CRIMPER III Hand Tool Assembly 318451–1
consists of Die Assembly 318451–2 and
PRO–CRIMPER III Hand Tool Frame 354940–1. The
hand tool assembly is used to crimp 75–Ohm RF
Series BNC Commercial Plug Connector 221185–8
and Bulkhead Jack Connector 221221–5 onto various
sizes of RG/U cable.
For connector assembly and cable stripping
procedures, refer to instruction sheet 408–9088 for
the plug connectors and 408–9089 for the jack
connectors. Read these instructions thoroughly
before using the hand tool assembly. This document
supersedes Instruction Sheet 408–9282.
Reasons for reissue of this instruction sheet are
provided in Section 9, REVISION SUMMARY.
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended–use, production operations is available.
The PRO–CRIMPER III Hand Tool is a “Commercial” grade tool and is
designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate 114 application specification, but may not comply with other
feature parameters of the specification. Tyco Electronics offers a variety of
tools to satisfy your performance requirements. For additional information,
contact the Tooling Assistance Center at 1–800–722–1111.
E
All International Rights Reserved
AMP and Tyco are trademarks. *Trademark
Other products, logos, and company names used are the property of their respective owners.
2004 Tyco Electronics Corporation, Harrisburg, PA
NOTE
Dimensions on this sheet are in millimeters
[with inches in brackets]. Figures are for
reference only and are not drawn to scale.
Die Assembly
318451–2
Moving
Jaw
Ratchet
Adjustment Wheel
This controlled document is subject to change.
For latest revision, call the FAX/PRODUCT INFO number.
PRO–CRIMPER* III Hand Tool
Assembly 318451–1 with
Die Assembly 318451–2
Figure 1
2. DESCRIPTION
The hand tool assembly features a tool frame with a
stationary jaw and handle, a moving jaw, a moving
handle, and an adjustable ratchet that ensures full
connector crimping.
The tool frame holds a die assembly with two
crimping chambers. The die assembly features a wire
anvil, an insulation anvil, a wire indenter, and an
insulation indenter. Die retaining pins and die retaining
screws are used to position and secure the dies in the
tool frame.
3. INSTALLATION AND REMOVAL OF DIE ASSEMBLY
(Figure 2)
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
Stationary
Jaw
Back of Tool
(Wire Side)
TOOLING ASSISTANCE CENTER 1–800–722–1111
FAX/PRODUCT INFO 1–800–522–6752
For Regional Customer Service, visit our website at
www.tycoelectronics.com
(Figures 1 and 2)
Moving Handle
PRO–CRIMPER III Hand
Tool Frame 354940–1 (See
Instruction Sheet 408–9930)
Stationary
Handle
Instruction Sheet
408–4217
12 MAY 04 Rev A
1 of 5
LOC B

318451-2 Summary of contents

Page 1

... For additional information, contact the Tooling Assistance Center at 1–800–722–1111. 1. INTRODUCTION PRO–CRIMPER III Hand Tool Assembly 318451–1 consists of Die Assembly 318451–2 and PRO–CRIMPER III Hand Tool Frame 354940–1. The hand tool assembly is used to crimp 75– ...

Page 2

... PRO–CRIMPER III Hand Tool Assembly 318451–1 Figure 2 4. CRIMPING PROCEDURE This tool is provided with a crimp adjustment NOTE feature ...

Page 3

... Ferrule Crimp Ferrule Anvil Die Rev A PRO–CRIMPER III Hand Tool Assembly 318451–1 5. INSPECTION 5.1. Visual Inspection The crimping dies should be inspected on a regular basis to ensure that they have not become worn or damaged. Inspect the crimping chambers for flattened, chipped, worn, or broken areas ...

Page 4

... Ferrule [.0950–.0953] [.1129–.1130] Figure PRO–CRIMPER III Hand Tool Assembly 318451–1 Insert the gage element for the insulation ferrule NOTE section into the back of the crimping chamber. The GO element for this section will not pass completely through the crimping chamber. ...

Page 5

... Rev A PRO–CRIMPER III Hand Tool Assembly 318451–1 CUSTOMER SERVICE (38–35) TYCO ELECTRONICS CORPORATION P.O. BOX 3608 HARRISBURG, PA 17105–3608 For customer repair service, contact a Tyco Electronics Representative at 1–800–526–5136. 9. REVISION SUMMARY Per EC 0990– ...