318450-2 Tyco Electronics, 318450-2 Datasheet

PROCRIMP DIE ASSY BNC TNC

318450-2

Manufacturer Part Number
318450-2
Description
PROCRIMP DIE ASSY BNC TNC
Manufacturer
Tyco Electronics
Type
Dier
Datasheets
1.1673606-1.pdf (8 pages)
2.318450-1.pdf (5 pages)
3.318450-1.pdf (5 pages)

Specifications of 318450-2

Connector Type
BNC, TNC
Crimp Handle
Tyco/AMP 318450-1
Crimp Or Cable Size
RG/U-161, 174, 179, 187, 188, 316
Crimp Tool
Hand Crimper III
Product
Tool Component
Description/function
O Crimp Commercial
Features
Die for Pro-Crimper
For Use With
SDE Dies
Lead Free Status / RoHS Status
Not applicable / Not applicable
Lead Free Status / RoHS Status
na, Not applicable / Not applicable
Other names
A24780
PROPER USE GUIDELINES
1. INTRODUCTION
PRO–CRIMPER III Hand Crimping Tool Assembly
318450–1 consists of Die Assembly 318450–2 and
PRO–CRIMPER III Hand Crimping Tool Frame
354940–1. The hand tool assembly is used to crimp
COAXICON* 50–Ohm RF Series BNC and TNC
Commercial Connectors 227079–[ ], 414168–[ ],
414171–3, and 414173–[ ] onto various sizes of RG/U
cable.
For connector assembly and cable stripping
procedures, refer to the instructions packaged with
the connector. For additional information on the hand
tool frame, refer to Instruction Sheet 408–9930. Read
these instructions thoroughly before using the hand
tool assembly.
E
PRO-CRIMPER* III Hand Crimping
Tool Assembly 318450-1 with
D ie Assembly 318450-2
Figure 1
2. DESCRIPTION
The hand tool assembly features a tool frame with a
stationary jaw and handle, a moving jaw, a moving
handle, and an adjustable ratchet that ensures full
connector crimping.
The tool frame holds a die assembly with two
crimping chambers. The die assembly features a wire
anvil, an insulation anvil, a wire indenter, and an
insulation indenter. Die retaining pins and die retaining
screws are used to position and secure the dies in the
tool frame.
NOTE
i
Dimensions on this sheet are in millimeters
[with inches in brackets]. Figures are not drawn
to scale.
www.tycoelectronics.com
408-4218
1

318450-2 Summary of contents

Page 1

... Instruction Sheet 408–9930. Read these instructions thoroughly before using the hand tool assembly. E PRO-CRIMPER* III Hand Crimping Tool Assembly 318450-1 with D ie Assembly 318450-2 Figure 1 NOTE Dimensions on this sheet are in millimeters [with inches in brackets]. Figures are not drawn i to scale ...

Page 2

... PRO-CRIMPER III Hand Crimping Tool Assembly 318450-1 Insulation Wire Indenter Indenter Wire Anvil Ferrule Crimping Chamber Insulation Anvil Center Contact Crimping Chamber 3. INSTALLATION AND REMOVAL OF DIE ASSEMBLY (Figure 2) 1. Open the tool handles and remove the two die retaining screws from the tool jaws. ...

Page 3

... PRO-CRIMPER III Hand Crimping Tool Assembly 318450-1 Center Contact Crimp Center Contact Flange Against Edge of Die Anvil Die Stripped Cable Figure 3 3. Allow the handles to open fully, and remove the crimped center contact from the die assembly. 4.2. Ferrule (Figure 4) 1. Flare the cable braid and insert the crimped ...

Page 4

Align the GO element with the crimping chamber. Push the element straight into the crimping chamber without using force. The GO element must pass completely through the crimping chamber. 3. Align the NO–GO element and try to insert it ...

Page 5

... S The TE logo was applied; S PRO–CRIMPER II became PROCRIMPER III; S Format was updated to current corporate requirements 3 2.64 +0.20 [.104 +.008] 4.32 +0.10 [.170 +.004] 5 11.63 [.458] INDENTER, Wire ANVIL, Wire INDENTER, Insulation ANVIL, Insulation PIN, Die Retaining Figure 7 Tyco Electronics Corporation 47.62 [1.88 ...