58436-3 Tyco Electronics, 58436-3 Datasheet - Page 3
58436-3
Manufacturer Part Number
58436-3
Description
DIESET HEXCRIMP RG174, 179, 180
Manufacturer
Tyco Electronics
Series
Pro-Crimper™ IIIr
Type
Dier
Specifications of 58436-3
Connector Type
BNC, TNC
Crimp Handle
A9996-ND
Crimp Or Cable Size
RG/U-161, 174, 179, 187, 188, 316
Crimp Application
Coaxial
Product
Tool Component
Description/function
BNC Hex Crimp
Features
Die for Pro-Crimper
Fits Cable/wire
161, 174, 179, 179A, 179B, 180, 180A, 187, 187A, 188, 188A, 195, 195A, 316, Belden 9221, C1180B
For Use With
Pro Crimper II Hand Crimp Tool & BNC Crimp Connectors
Lead Free Status / RoHS Status
Not applicable / Not applicable
Lead Free Status / RoHS Status
na, Not applicable / Not applicable
Other names
A9995
The die assembly will perform correctly as long as:
(1) the product specified is correct for the application,
(2) the specific die assembly is used, (3) the die
assembly has been measured to ensure that the
openings are correct, and (4) the tool has been
adjusted correctly.
Figure 5 provides information on die opening sizes.
The tool frame assembly ratchet mechanism features
an adjustment wheel with eight settings. The
adjustment wheel controls the amount of handle
pressure exerted on the tool jaws and crimping dies
during crimping. If the crimp is not acceptable, adjust
the ratchet as follows:
Rev
1. Sufficiently loosen the screw at the ratchet
adjustment wheel so that the wheel can be rotated
above the post that engages the teeth in the wheel.
2. If the crimp is too loose, turn the wheel to a
higher notch (for example, if the wheel is set at
notch no. 5, move the wheel to notch no. 6). If the
crimp is too tight, move the wheel to a lower notch.
3. Tighten the screw at the ratchet
adjustment wheel.
A"
58425-1
58425-2
58425-3
58436-1
58436-2
58436-3
58436-4
B"
Die 58425-[ ]
1.07 [.042] (Square)
1.07 [.042] (Square)
1.07 [.042] (Square)
---
---
---
---
Tyco Electronics Corporation
C"
5.41 [.213] (Hex)
3.25 [.128] (Hex)
3.84 [.151] (Hex)
5.41 [.213] (Hex)
2.54 [.100] (Hex)
3.84 [.151] (Hex)
3.73 [.147] (Hex)
Figure 5
If the crimp cannot be made to conform to the
dimensions provided in the appropriate product
application specification, the tool and/or dies are
defective and must be replaced.
Customer–replaceable parts are shown in Figure 1.
Available separately, PRO–CRIMPER Repair Kit
679221–1 includes a variety of pins, rings, screws,
and springs. If the dies are damaged or worn
excessively, they must be replaced. Order the repair
kit and replaceable parts through your Tyco
Electronics Representative, or call 1–800–526–5142,
or send a facsimile of your purchase order to
1–717–986–7605, or write to:
D"
CUSTOMER SERVICE (38–35)
TYCO ELECTRONICS CORPORATION
P.O. BOX 3608
HARRISBURG, PA 17105–3608
S Updated logo and format.
i
B"
Other dies of the PRO-CRIMPER hand tool
series may be used in this tool; however, the
ratchet adjustment wheel may require adjustment
to achieve acceptable crimp height.
6.48 [.255] (Hex)
4.52 [.178] (Hex)
8.23 [.324] (Hex)
6.48 [.255] (Hex)
8.23 [.324] (Hex)
4.52 [.178] (Hex)
4.52 [.178] (Hex)
Die 58436-[ ]
1.73 [.068] (Hex)
1.73 [.068] (Hex)
1.73 [.068] (Hex)
1.73 [.068] (Hex)
---
---
---
C"
of 3