47823 Tyco Electronics, 47823 Datasheet - Page 4

• Manufacturer Part Number: 47823
• Description: DIE TERMINYL 69051 2AWG
• Manufacturer: Tyco Electronics

Specifications of 47823

• Lead Free Status / RoHS Status: Not applicable / Not applicable

Splices with Step-Down Adapter
8 to 16-14
8 to 12-10
of 8
3. Insert stripped wire into the wire barrel of the
end of the splice to be crimped until the wire
bottoms against the wire stop within the splice.
Refer to Figure 3.
4. Remove crimping head latch pin, and open
yoke.
5. Place the splice in the stationary die. Grasp the
end of the splice to be crimped and point the
opposite end toward the top of the head yoke at
approximately a 30 _ angle. Rotate the end of the
splice to be crimped into the die. Position the edge
of the window indent against the locator. Refer to
Figure 5.
6. Holding the splice in place, close the yoke and
insert the latch pin.
7. Holding the wire in place, activate tool or power
unit to complete first wire barrel crimp.
8. When crimp is completed, remove the latch pin,
open the yoke and remove splice.
9. To crimp the other half of splice, reposition
uncrimped end of splice in the stationary die and
follow the same procedure used to crimp the first
half of splice.
10. Inspect the crimp according to Section 5.
1/0 to 2
6 to 8
4 to 8
4 to 6
2 to 4
!
i
Be sure that the latch pin is fully inserted, or
damage to the dies and tool or head will occur
when the tool is activated.
If splice sticks in die after crimping, apply a
rocking action to the splice to remove it from the
die. Wipe light oil on dies to reduce sticking, or
use spray dry lubricant.
É É É É
É É É É É É É É
47820
47820
47821
47822
47822
47823
47824
Ç Ç Ç Ç Ç Ç
Ç Ç Ç Ç Ç Ç
Figure 6
É É É É
Yellow
Yellow
Blue
Blue
Red
Red
Red
Step-Down Adapter
Yellow
Yellow
Tyco Electronics Corporation
Blue
Blue
Red
Red
Red
Crimping Butt Splices
Locator Removed
from Stationary Die
1. Strip wires to the dimensions listed in Figure 3.
Do not nick or cut the wire strands.
2. Select the proper color–coded butt splice for the
wire size. The wire size stamped on the butt splice
and on the crimping die must match the wire size
selected.
3. Remove crimping head latch pin, and open
yoke. Remove the stationary die from the yoke,
then remove the locator from the stationary die.
Re–assemble the stationary die onto the yoke.
4. Insert the stripped wire into the wire barrel of the
end of the butt splice to be crimped until the wire
bottoms against the wire stop within the splice.
5. Place the butt splice in the stationary die with
the wire barrel of the end of the splice to be
crimped centered over the crimping chamber. See
Figure 7.
6. Holding butt splice in place, close the yoke and
insert the latch pin.
7. Holding wire in place, activate tool or power unit
to complete first wire barrel crimp.
8. When crimp is completed, remove the latch pin,
open the yoke and remove the butt splice.
Wire Barrel in
Stationary Die
Centered Over
Crimping Chamber
!
!
Avoid personal injury. When operating tool or
power unit, exercise caution while holding butt
splices or wire near the crimping area.
To avoid damage to the dies, be sure that the
stationary die is properly oriented with the
moving die.
Be sure that the latch pin is fully inserted,
otherwise damage to the die and tool or head will
occur when the tool or power unit is activated.
Figure 7
Rev