58423-1 Tyco Electronics, 58423-1 Datasheet

DIESET SPLICE TERMINALS

58423-1

Manufacturer Part Number
58423-1
Description
DIESET SPLICE TERMINALS
Manufacturer
Tyco Electronics
Series
Pro-Crimper™ IIIr
Type
Crimp Tool Assemblyr
Datasheets
1.1673606-1.pdf (8 pages)
2.58433-3.pdf (4 pages)
3.58423-1.pdf (4 pages)

Specifications of 58423-1

Connector Type
Terminals and Splices
Crimp Handle
A9996-ND
Crimp Or Cable Size
10-22 AWG
Die Set, For Insulated Terminals And Splices,cable Wrap,sde Tooling Pro-crimper Iii Hand Tool ,tyco Electronics / Amp
ROHS COMPLIANT
Product
Crimping, Stripping & Cutting Tools & Drills
Lead Free Status / RoHS Status
Not applicable / Not applicable
Lead Free Status / RoHS Status
Not applicable / Not applicable
Other names
A9991
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended- - use, production operations is available.
1. INTRODUCTION
PRO--CRIMPER III Hand Crimping Tool Assembly
58433--3 consists of PRO--CRIMPER III Hand
Crimping Tool Frame 354940--1 and Die Assembly
58423--1. The tool assembly is used to crimp the
terminals listed in Figure 1 . For additional information
on the hand tool frame, refer to 408--9930. Read
these instructions thoroughly before using the tool
assembly.
Reasons for reissue of this instruction sheet are
The PRO- - CRIMPER III Hand Crimping Tool is a “Commercial” grade
hand tool and is designed primarily for field installation, repair,
maintenance work, or prototyping in industrial, commercial, or
institutional applications. Product crimped with this tool will meet
the crimp height requirement for hand tools in the appropriate 114 Series
Specification, but may not comply with other feature parameters of the
specification. A variety of tools are offered to satisfy your performance
requirements. For additional information, contact the Tooling Assistance
Center at 1- - 800- - 722- - 1111.
Note: Refer to Catalogs 82004 and 82042 for terminal selection information.
E2010 Tyco Electronics Corporation, Berwyn, PA
All Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other product names, logos, or company names might be trademarks of their respective owners.
PLASTI--GRIP* Terminal
PLASTI--GRIP* Terminal
PIDG* Terminal or
PIDG FASTON*
PIDG FASTON
Terminal
Family
Product
Die Assembly
Moving
Jaw
Stationary
Jaw
Ratchet
Adjustment Wheel
Insulation
Yellow
Color
Blue
Blue
Red
Red
TOOLING ASSISTANCE CENTER 1- - 800- - 722- - 1111
PRODUCT INFORMATION 1- - 800- - 522- - 6752
PRO- CRIMPER* III Hand Crimping
Tool Assembly 58433- 3 with
Die Assembly 58423- 1
Size (AWG)
Figure 1
22--16
16--14
12--10
22--18
16--14
provided in Section 9, REVISION SUMMARY.
CAUTION
NOTE
i
!
Pivot Pin
Maximum Insulation
Diameter (mm [in.])
Back of Tool
(Wire Side)
Dimensions in this instruction sheet are in
millimeters [with inches in brackets]. Figures are
not drawn to scale.
Terminals crimped with Tool 58433- - 3 or with
Die Assembly 58423- - 1 are not Listed by
Underwriters Laboratories Inc. (UL) or CSA
International.
3.56 [.140]
4.32 [.170]
6.35 [.250]
3.56 [.140]
4.32 [.170]
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
PRO- - CRIMPER III Hand
Crimping Tool Frame
354940- - 1 (408- - 9930)
Wire
Moving Handle
Stationary Handle
5.15--5.95 [.203--.234]
5.15--5.95 [.203--.234]
7.94--8.73 [.312--.344]
8 33 9 14 [ 328 360]
8.33--9.14 [.328--.360]
Range (mm [in.])
Strip Length
Instruction Sheet
408- - 9252
15 APR 10 Rev J
1 of 4
LOC B

58423-1 Summary of contents

Page 1

... PRO--CRIMPER III Hand Crimping Tool Assembly 58433--3 consists of PRO--CRIMPER III Hand Crimping Tool Frame 354940--1 and Die Assembly 58423--1. The tool assembly is used to crimp the terminals listed in Figure 1 . For additional information on the hand tool frame, refer to 408--9930. Read these instructions thoroughly before using the tool assembly ...

Page 2

... Section 5. 5. CRIMP HEIGHT INSPECTION This inspection requires the use of calipers. A lead rod can be used to check the crimp height. Crimp a rod in each of the crimping chambers. Check the crimp height of the rod against the crimp height dimension given in Figure 4. Tyco Electronics Corporation Rev J ...

Page 3

... If the dies are damaged or worn excessively, they must be replaced. Order the repair kit and replaceable parts through your representative, or call 1--800--526--5142, or send a facsimile of your purchase order to 717--986--7605, or write to: Tyco Electronics Corporation Screwdriver Lockscrew Figure ...

Page 4

... Manual 409- 10053 Added illustration showing the tooling S compatible with Dies 58423--1; Updated format S Tooling Compatible with Dies 58423- 1 (Instruction Sheet 408- 4070) Tyco Electronics Corporation SDE- SA Hand Tool 9- 1478240- 0 (Instruction Sheet 408- 8851) 626 Adapter 679304- 1 Battery Tool (Pin Die) 1213890 ...