45575-1 Tyco Electronics, 45575-1 Datasheet - Page 5
45575-1
Manufacturer Part Number
45575-1
Description
DAHT PG BUTT 14-16
Manufacturer
Tyco Electronics
Series
Certi-Crimp™ II, Plasti-Grip™r
Specifications of 45575-1
Tool Type
Hand Crimper
Features
Side Entry, Ratchet
For Use With/related Products
Splices, 14-22 AWG
For Use With
328427 - CONN BUTT SPLICE 14-16AWG NATRL8-34204-1 - SPLICE PG BUTT 16-148-55792-1 - SPLC,BUTT,PG 22-16COMM22-18MIL8-324138-1 - PG BUTT SPLC 22-16COMM22-18MIL2-35244-1 - CONN SPLICE BUTT 16-14AWG8-35244-1 - CONN SPLICE BUTT 16-14AWG STD8-34068-1 - CONN SPLICE BUTT 16-14AWG STD8-328427-1 - CONN SPLICE BUTT 16-14AWG STD8-55785-1 - CONN SPLICE BUTT 16-14AWG TIN55792-1 - CONN BUTT SPLICE 16-22AWG RED324138 - CONN SPLICE BUTT 22-16AWG TIN8-34243-1 - CONN SPLICE BUTT 22-16AWG REDA28185 - CONN SPLICE BUTT 14-16AWG BLUE8-34071-1 - CONN SPLICE BUTT 14-16 AWG P-G8-34070-1 - CONN SPLICE BUTT 16-22 AWG P-G8-34067-1 - CONN SPLICE BUTT 16-22 AWG P-GA27462 - CONN SPLICE BUTT 16-22 AWG P-GPA27542 - CONN SPLICE BUTT 14-16 AWG CLRA27465 - CONN SPLICE BUTT 14-16 AWG PL-GPA27463 - CONN SPLICE BUTT16-22 AWG PL-GPA27464 - CONN SPLICE BUTT 14-16 AWG .140A09034 - CONN SPLICE BUTT 14-16 AWG P-GPA09033 - CONN SPLICE BUTT 16-22 AWG .120A0998 - CONN SPLICE BUTT 14-16 AWG .170A0997 - CONN SPLICE BUTT 16-22 AWG .140
Lead Free Status / RoHS Status
Not applicable / Not applicable
Other names
A27987
Rev H
If the crimping chamber conforms to the gage
inspection, the tool is considered dimensionally
correct, and should be lubricated with a THIN coat of
any good SAE 20 motor oil. If not, refer to Section 6,
REPLACEMENT AND REPAIR for obtaining further
evaluation and repair.
For additional information regarding the use of plug
gages, refer to instruction sheet 408--7424.
5.5. CERTI- CRIMP Tool Ratchet Inspection
The CERTI-CRIMP tool ratchet should be checked to
ensure that the ratchet does not release prematurely,
allowing the jaws to open before they have fully
bottomed. Obtain a 0.025 [.001] shim that is suitable
for checking the clearance between the bottoming
surfaces of the crimping jaws. Proceed as follows:
6. REPLACEMENT AND REPAIR
Customer-replaceable parts are listed in Figure 7. A
complete inventory should be stocked and controlled
to prevent lost time when replacement of parts is
necessary. Parts other than those listed should be
replaced by Tyco Electronics to ensure quality and
reliability. Order replacement parts through your Tyco
Electronics representative, or call 1-800--526--5142,
or send a facsimile of your purchase order to 717-
986-7605, or write to:
4. Insert insulation crimp adjustment pins into
Position 1.
5. Check the insulation barrel section of the
crimping chamber using the insulation crimp
plug gage in the same manner as in Steps 2 and
3. See Figure 6, Detail B.
1. Select a splice and maximum size wire for the
tool.
2. Position the splice and wire in tool as
described in Section 3, CRIMPING
PROCEDURE.
3. Hold the wire in place and squeeze the
handles until the ratchet releases. Hold the
handles in this position, maintaining just enough
tension to keep the jaws closed.
4. Close the tool handles until it is evident that
the jaws have bottomed; then hold in this
position. Do NOT force the jaws beyond initial
contact.
5. Check the clearance between the bottoming
surfaces of the crimping jaws. If the clearance is
0.025 [.001] or less, the ratchet is satisfactory. If
clearance exceeds 0.025 [.001], the ratchet is
out of adjustment and must be repaired. See
Section 6, REPLACEMENT AND REPAIR.
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
For customer repair service, please contact a Tyco
Electronics representative at 1-800-526-5136.
7. REVISION SUMMARY
Revisions to this instruction sheet include:
•
•
Logo changed
Format updated
408-1502
5 of 6