543344-1 Tyco Electronics, 543344-1 Datasheet - Page 2
543344-1
Manufacturer Part Number
543344-1
Description
TOOL HAND CRIMP FOR FERRULE DIE
Manufacturer
Tyco Electronics
Series
AMPLIMITE®r
Type
Crimp Toolr
Datasheet
1.543344-1.pdf
(4 pages)
Specifications of 543344-1
Tool Type
Handle, Frame - without Die Set
Features
Side Entry, Ratchet
Product
Crimping, Stripping & Cutting Tools & Drills
For Use With
58238-1 - DIE SET SHELL SIZE 4-5 .375-.43558237-2 - DIE ASSY AMPLIMITE .422-.490MM58237-1 - DIE ASSY AMPLIMITE .480-.562MM543425-1 - DIE AMPLMT FERR 530/353543013-9 - TOOL DIE SET ASSY 10.59MM543013-8 - TOOL DIE SET ASSY 10.59MM543013-7 - TOOL DIE SET ASSY 10.59MM543013-6 - TOOL DIE SET ASSY 9.19MM543013-5 - TOOL DIE SET ASSY 8.51MM543013-3 - TOOL DIE SET ASSY 6.10MM543013-2 - TOOL DIE SET ASSY 6.10MM543013-1 - TOOL DIE SET ASSY 6.10MM1-543013-7 - TOOL DIE SET CRIMP .280 CABLE1-543013-6 - TOOL DIE SET CRIMP .280 CABLE1-543013-4 - TOOL DIE SET CRIMP .650 CABLE1-543013-3 - TOOL DIE SET CRIMP .650 CABLE1-543013-2 - TOOL DIE SET CRIMP .530 CABLE1-543013-1 - TOOL DIE SET CRIMP .525 CABLE1-543013-0 - TOOL DIE SET CRIMP .530 CABLE1583015-3 - TOOL .236 DIE ASSY HSSDC II1583015-2 - TOOL .210 DIE ASSY HSSDC II543425-2 - TOOL DIE SET FOR HDP-20543013-4 - CRIMPER ANVIL SUBASSYA23584 - TOOL DIE SET FOR STRIGHT FERRULEA23583 - TOOL DIE SET FOR STRIGHT FERRULEA23582 - TOOL DIE SET FOR STEPPED FERRULEA23581 - TOOL DIE SET FOR STEPPED FERRULEA23580 - TOOL DIE SET FOR STEPPED FERRULEA23579 - TOOL DIE SET FOR STEPPED FERRULEA23578 - TOOL DIE SET FOR STEPPED FERRULEA23577 - TOOL DIE SET FOR STEPPED FERRULE
Lead Free Status / RoHS Status
Not applicable / Not applicable
For Use With/related Products
Varies by Die Set
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
A23576
4. CRIMPING PROCEDURE
5. MAINTENANCE AND INSPECTION
It is recommended that a maintenance and inspection
program be performed periodically to ensure
dependable and uniform terminations. Though
recommendations call for at least one inspection a
month, frequency of inspection depends on:
2 of 4
1. Close the handles until the ratchet releases.
Allow the handles to open FULLY.
2. Open the latch, and looking into the front of the
tool, insert the cable and ferrule into the back of
the crimping chamber. Position the ferrule in the
dies according to the instructions included with the
dies. Close the latch.
NOTE
3. Close the tool handles until the ferrule is held
firmly in place.
4. Squeeze the tool handles together until the
ratchet releases. Allow the handles to open FULLY,
open the latch, and remove the crimped ferrule.
1. The care, amount of use, and handling of the
tool.
2. The presence of abnormal amounts of dust and
dirt.
3. The degree of operator skill.
4. Your own established standards.
i
Crimper
(Stationary Die)
Always refer to instruction sheet packaged with
the dies for positioning of the ferrule in the dies.
Anvil
(Moving Die)
Die Holding
Screw
Front of Tool
Figure 2
The tool is inspected before being shipped; however,
it is recommended that the tool be inspected
immediately upon arrival to ensure that the tool has
not been damaged during shipment.
5.1. Daily Maintenance
5.2. Periodic Inspection
A. Lubrication
Lubricate all pins, pivot points, and bearing surfaces
with any good SAE 20 motor oil as follows:
Wipe excess oil from the tool, particularly from the
crimping area. Oil transferred from the crimping area
1. Immerse the tool (handles partially closed) in a
reliable commercial degreasing compound to
remove accumulated dirt, grease, and foreign
matter. When degreasing compound is not
available, the tool may be wiped clean with a soft,
lint--free cloth. DO NOT use hard or abrasive
objects that could damage the tool.
2. Make certain that the retaining pins are in place
and that they are secured with retaining rings.
3. All pins, pivot points, and bearing surfaces
should be protected with a THIN coat of any good
SAE 20 motor oil. DO NOT oil excessively.
4. When the tool is not in use, keep the handles
closed to prevent objects from becoming lodged in
the crimping dies. Store the tool in a clean, dry
area.
Tool used in daily production — daily
Tool used daily (occasional) — weekly
Tool used weekly — monthly
Lower Die Holder
Die Holder Plate
Latch
408- 9315
Rev C