90652-1 Tyco Electronics, 90652-1 Datasheet

no-image

90652-1

Manufacturer Part Number
90652-1
Description
PRO-CRIMPER ASSY MULTILOCK
Manufacturer
Tyco Electronics
Datasheet
1.90652-1.pdf (6 pages)

Specifications of 90652-1

Lead Free Status / RoHS Status
Not applicable / Not applicable
Features
-
For Use With/related Products
-
Tool Type
-
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended- - use, production operations is available.
1. INTRODUCTION
PRO--CRIMPER III Hand Crimping Tool
Assembly 90653--1 consists of Die Assembly
90653--2 and PRO--CRIMPER III Hand Crimping Tool
Frame 354940--1. The die assembly consists of
crimping dies and a locator assembly.
Read these instructions thoroughly before crimping
The PRO- - CRIMPER III Hand Crimping Tool is a “Commercial” grade tool
and is designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate 114 series specification, but may not comply with other feature
parameters of the specification. Tyco Electronics offers a variety of tools to
satisfy your performance requirements. For additional information, contact the
Technical Assistance Center at 1- - 800- - 722- - 1111.
E2009 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
{
TE Die Assembly
90652--2
Supplied with die assembly. Also available separately.
Font of Tool
(Locator Side)
Locator
Assembly
(Supplied with
Die Assembly)
Locator Assembly
Die
Assembly
58515--1
Ratchet Adjustment Wheel
Moving Jaw
{
TOOLING ASSISTANCE CENTER 1- - 800- - 722- - 1111
PRODUCT INFORMATION 1- - 800- - 522- - 6752
PRO- CRIMPER* III Hand
Crimping Tool Assembly 90652- 1
with Die Assembly 90652- 2
Contact Family
} Contact the Tooling Assistance Center or Product Information (below) for specific contact part numbers.
.040 Series
Contacts
Contacts
M ltil k
Multilock
Figure 1
}
any contacts.
Reasons for reissue are provided in Section 11,
REVISION SUMMARY.
NOTE
i
(AWG)
Size
Stationary Jaw
20
18
22
Pivot Pin
Dimensions on this sheet are in millimeters [with
inch equivalents provided in brackets]. Figures
and illustrations are for identification only and are
not drawn to scale.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
Moving
Handle
[.063 to .083]
[.071 to .091]
[.055 to .075]
1.60 to 2.11
1.80 to 2.31
1.40 to 1.90
(mm [In.])
Insul Dia
Back of Tool
(Wire side)
PRO- - CRIMPER III Hand
Crimping Tool Frame
354940- - 1 (408- - 9930)
Wire
Stationary
Handle
Instruction Sheet
408- - 9853
17 AUG 09 Rev C
Strip Length
[.175 to .177]
3.99 to 4.50
(mm [In.])
1 of 6
LOC B

90652-1 Summary of contents

Page 1

... All International Rights Reserved TE logo and Tyco Electronics are trademarks. *Trademark. Other products, logos, and company names used are the property of their respective owners. PRO- CRIMPER* III Hand Crimping Tool Assembly 90652- 1 with Die Assembly 90652- 2 Stationary Jaw Pivot Pin Size { ...

Page 2

... To disassemble, close the tool handles until the ratchet releases, remove the nut, the locator assembly, the two die retaining screws, and the four die retaining pins, and slide the anvils and crimpers out of the tool jaws. Tyco Electronics Corporation Tool Frame Die Retaining Pins Die Retaining Screws ...

Page 3

... Refer to Figure 3. Butt the front end of the wire barrel against the movable locator. Back of Tool (Wire Side) Contact (Typ) Wire Locator in Wire Stop Slot Figure 3 Tyco Electronics Corporation Strip Length Wire Inserted to Stop ...

Page 4

... If the dimension is acceptable, replace and secure the lockscrew. If the dimension is unacceptable, continue to adjust the ratchet, and again measure a sample crimp. Screwdriver Ratchet Adjustment Wheel Lockscrew (Typ) Tyco Electronics Corporation “A” Crimp Height Dimension (A) Dimension (A) Tolerance (+.) .927 + .051 20 [.036 + .0020] 1.041 + .051 18 [ ...

Page 5

... PO BOX 3608 HARRISBURG PA 17105--3608 11. REVISION SUMMARY Revisions to this instruction sheet include: Changed PRO--CRIMPER II Hand Tool to S PRO--CRIMPER III Hand Tool; Added back page (tooling using die assembly S 90652--2); Added TE logo; and S Updated format to current corporate S requirements. Tyco Electronics Corporation ...

Page 6

... Die Assembly 90652- 2 Can Be Used In the Following Tools: PRO- CRIMPER III Hand Tool 354940- 1 (Instruction Sheet 408- 9930) SDE Bench Terminator 1490076- 2 (Customer Manual 409- 10052) Battery Tool (Shouldered Die) 1725837 (Customer Manual 409- 10053 SDE PEW- 12 Hand Tool 9- 1478240- 0 (Instruction Sheet 408- 8851) ...