64001-0400 Molex Inc, 64001-0400 Datasheet - Page 3

• Manufacturer Part Number: 64001-0400
• Description: TOOL HAND CRIMP 10-22 AWG
• Manufacturer: Molex Inc
• Series: Insulkrimp®r

Specifications of 64001-0400

• Features: Side Entry, Ratchet
• Tool Type: Hand Crimper
• Product: Crimping, Stripping & Cutting Tools & Drills
• Fits Cable/wire: 22-10 AWG
• Crimp Size: 22AWG To 10AWG
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• For Use With/related Products: Quick Connects Terminals, 10-22 AWG
• For Use With: WM18722 - CONN FEMALE FO .250 14-16AWG BLUWM18721 - CONN FEMALE FO .250 18-22AWG REDWM18760 - CONN .110" FEMALE INSUL 18-22AWGWM18759 - CONN .187" FEMALE INSUL 18-22AWG19003-0047 - .250 FEMALE INSULATED 14-16 AWG19003-0059 - QUICK DISCONN FEMALE 14-16 AWGWM5929 - CONN .250" FEMALE INSUL 14-16AWGWM5928 - CONN .187" FEMALE INSUL 18-22AWGWM18241 - CONN .250" FEMALE INSUL 10-12AWGWM18240 - CONN .187" FEMALE INSUL 14-16AWGWM18239 - CONN .250" FEMALE INSUL 14-16AWGWM18238 - CONN .187" FEMALE INSUL 18-22AWGWM18237 - CONN .250" FEMALE INSUL 18-22AWG
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 064001-0400; 064001-0400-E; 0640010400; 0640010400-E; 64001-0400-E; 64001-0400; 640010400; 640010400-E; Q1905044; Q2941097; WM1622

RHT 1994 Hand Crimp Tool
Doc No. 64001-0400
Revision: G
Maintenance
It is recommended that each operator of the tool
be made aware of, and responsible for, the
following maintenance steps:
1. Remove dust, moisture and other
2. Do not use any abrasive materials that could
3. Make certain all pins; pivot points and
4. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies, and store the tool in
Miscrimps or Jams
Should this tool ever become stuck or jammed in a partially closed position,
easily by pressing the ratchet release lever (See Fig.5).
How To Adjust Tool Preload
Over the life of the tool, it may be necessary to adjust tool
handle preload force. Listed below are the steps required
to adjust the crimping force of the hand tool to obtain
proper crimp conditions:
1. Remove the screw and plastic cover washer. Note the
2. Lift the setting wheel off the axle. Turn the eccentric
3. Turning the eccentric axle counter-clockwise will
4. Replace the setting wheel to the axle, aligning the
5. Replace the plastic cover washer and screw.
6. Check the crimp specifications after tool crimp force is adjusted.
contaminants with a clean brush, or soft, lint-
free cloth.
damage the tool.
bearing surfaces are protected with a thin
coat of high quality machine oil. Do not oil
excessively. The 64001-0400 (RHT-1994)
was engineered for durability, but like any fine piece of equipment it needs cleaning and lubrication for a maximum service life of
trouble-free crimping. A light oil, such as 30 weight automotive oil used at the oil points shown in Figure 4, every 5,000 crimps or
3 months will significantly enhance the tool life and ensure a stable calibration.
a clean, dry area.
setting wheel position.
axle with a screwdriver.
increase handle force.
nearest notch in the setting wheel to the dowel pin.
Release Date: 09-20-02
Revision Date: 07-21-05
(See Fig. 5)
M4 SCREW
LOOSEN
3/32” HEX
WRENCH
UNCONTROLLED COPY
RATCHET RELEASE
LEVER PUSH UP
Do Not force the handles open or
LOCKING SCREW
Figure 4
ADJUSTMENT
PRELOAD
TEST POINT
PRELOAD
TEST POINT
PRELOAD
(BOTH SIDES) LIGHT OIL
LUBRICATION POINTS
OR 5,000 CRIMPS)
(EVERY 3 MONTHS
closed. The tool will open
Figure 5
1.00
1.00
Page 3 of 6