46673 Tyco Electronics, 46673 Datasheet

TOOL HAND CRIMP STRATO 16-22AWG

46673

Manufacturer Part Number
46673
Description
TOOL HAND CRIMP STRATO 16-22AWG
Manufacturer
Tyco Electronics
Series
Certi-Crimp™, Strato-Therm™r
Datasheet
1.46673.pdf (6 pages)

Specifications of 46673

Tool Type
Hand Crimper
Features
Side Entry, Ratchet
Lead Free Status / RoHS Status
Not applicable / Not applicable
For Use With/related Products
Splices and Terminals, 16-22 AWG
Lead Free Status / RoHS Status
na, Not applicable / Not applicable
STRATO–THERM Hand Crimping Tools
46673, 46673–1, and 46988 are used to crimp
high–temperature and heat–resistant
STRATO–THERM terminals and splices onto wire
sizes 22 through 14 AWG.
Reasons for reissue of this instruction sheet are
provided in Section 7, REVISION SUMMARY.
Each hand tool features an indenter crimping jaw, an
anvil crimping jaw, locator, two insulation crimping
adjustment pins, and a CERTI–CRIMP ratchet. The
hand tool has the wire size marked on the BACK side
of the tool. The locator positions the terminal or splice
between the crimping jaws. The insulation crimping
adjustment pins are used to regulate the crimp height
of the insulation barrel sleeve.
E
i
All dimensions on this document are in metric
units [with U.S. customary units in brackets].
Figures and illustrations are for identification only
and are not drawn to scale.
Figure 1
The CERTI–CRIMP ratchet assures full crimping of
the terminal. Once engaged, the ratchet will not
release until the tool handles have been FULLY
closed. See Figure 1.
S
1. Strip wire using the recommended strip–length
dimensions provided in Figure 2.
!
S
The crimping jaws bottom before the
CERTI-CRIMP ratchet releases. This design
feature ensures maximum electrical and tensile
performance of the crimp. Do NOT re-adjust the
ratchet.
Figure 2

46673 Summary of contents

Page 1

... STRATO–THERM Hand Crimping Tools 46673, 46673–1, and 46988 are used to crimp high–temperature and heat–resistant STRATO–THERM terminals and splices onto wire sizes 22 through 14 AWG. All dimensions on this document are in metric units [with U.S. customary units in brackets]. Figures and illustrations are for identification only i and are not drawn to scale ...

Page 2

... Through Slot in Locator Figure 3 Splice Crimp (First Crimp) Wire Barrel Sleeve Push Locator Up So That Splice Slides Through Slot in Locator Figure 4 Tyco Electronics Corporation 408-1535 Back Side of Tool Insert Wire Conductor Through Insulation Barrel Sleeve and into Wire Barrel Sleeve Back Side ...

Page 3

... Step 4. Adjust pins, as necessary, until the desired insulation grip is obtained. Do not use a tighter setting than is required. NOTE The insulation crimping adjustment pins must be located in the same adjustment position. i Properly Crimped Terminal and Splice Tool 46673 and 46673-1 1 Hashmark Tool 46988 2 Hashmarks Figure 6 Tyco Electronics Corporation 408-1535 1 Hashmark on ...

Page 4

... Suggested Plug Gage Design for Insulation Barrel Section of Crimping Chamber GO Dim. GO W" 6.35 [.250] Min Typ Jaw Closure Configuration 46673 0.762-0.770 46673-1 [.0300-.0303] 1.016-1.024 46988 [.0400-.0403] Figure 7 Tyco Electronics Corporation NO-GO Dim. R" 1.648-1.651 [.0649-.0650] 1.57 [ ...

Page 5

... Replaceable parts are listed in Figure 9. Parts other than those listed in Figure 9 should be replaced to ensure quality and reliability of the tool. Order replacement parts through your Tyco Electronics Representative, or call 1–800–526–5142, or send a facsimile of your purchase order to 1–717–986–7605, or write to: CUSTOMER SERVICE (38– ...

Page 6

... STRATO-THERM Hand Crimping Tools Tools may also be returned for evaluation and repair. For tool repair service, please contact a Tyco Electronics Representative at 1–800–526–5136. ITEM PART NUMBER 6 7. REVISION SUMMARY Since the previous release of this sheet, the following changes were made: ...