58707-1 Tyco Electronics, 58707-1 Datasheet - Page 4

• Manufacturer Part Number: 58707-1
• Description: TOOL CRIMP W/DIE SET 16-20AWG
• Manufacturer: Tyco Electronics
• Series: Pro-Crimper™ III, Mini Universal MATE-N-LOK®r

Specifications of 58707-1

• Tool Type: Hand Crimper
• Features: Side Entry, Ratchet
• Product: Crimping, Stripping & Cutting Tools & Drills
• For Use With/related Products: Rectangular Contacts, 16-20 AWG
• For Use With: A34924 - CONN PIN 16-20AWG GOLD CRIMPA32447 - CONN SOCKET 16-20AWG GOLD CRIMPA28815 - CONN SOCKET 16-20AWG GOLD CRIMPA28814 - CONN SOCKET 16-20AWG TIN CRIMPA28807 - CONN PIN 16-20AWG GOLD CRIMPA28806 - CONN PIN 16-20AWG TIN CRIMPA25691 - CONN PIN 16-20AWG TIN CRIMPA25692 - CONN SOCKET 16-20AWG TIN CRIMP
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• Other names: A30726

6. CRIMP HEIGHT INSPECTION
Crimp height inspection is performed through the use
of a micrometer with a modified anvil, commonly
referred to as a crimp--height comparator. Tyco
Electronics does not manufacture or market
crimp--height comparators. Detailed information on
obtaining and using crimp--height comparators can be
found in instruction sheet 408--7424.
Proceed as follows:
4 of 5
CAUTION
4. Hold the contact in position and squeeze the
tool handles together until ratchet engages
sufficiently to hold the contact in position. Do NOT
deform insulation barrel or wire barrel.
5. Insert stripped wire into contact insulation and
wire barrels until it is butted against the wire stop,
as shown in Figure 3.
6. Holding the wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles
to open and remove crimped contact.
NOTE
7. Check the contact’s crimp height as described in
Section 6, CRIMP HEIGHT INSPECTION. If
necessary, adjust the crimp height as described in
Section 7, RATCHET (Crimp Height)
ADJUSTMENT.
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
RATCHET (Crimp Height) ADJUSTMENT.
i
!
Make sure that both sides of the insulation barrel
are started evenly into the crimping section. Do
NOT attempt to crimp an improperly positioned
contact.
The crimped contact may stick in the crimping
area, but the contact can be easily removed by
pushing downward on the top of the locator (see
Figure 3).
Tyco Electronics Corporation
7. RATCHET (Crimp Height) ADJUSTMENT
Position Point
on Center of
Wire Barrel
Opposite
Seam
Modified Anvil
AWG (Maxi
AWG (Maxi-
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. With a screwdriver, adjust the ratchet wheel
from the locator side of the tool.
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a
higher--numbered setting. If a looser crimp is
required, rotate the adjustment wheel
CLOCKWISE to a lower--numbered setting.
Wire Size
mum)
Ratchet
Adjustment
Wheel
18
16
Lockscrew
(Typ)
Screwdriver
(Wire Size Marking)
Crimp Section
Crimp Section
16, 2 (20)
20--18
Figure 5
Figure 4
“A”
Crimp Height
+.051 [+.002]
Dim. (A) and
Dim. (A) and
Tolerance
1.07 [.042]
1.30 [.051]
(Figure 5)
Rev A